BH150 Backhoes and BH160 Backhoes For Skid Steer Loaders and Multi Terrain Loaders Shipping Caterpillar


Shipping
`
BH150 Backhoes and BH160 Backhoes For Skid Steer Loaders and Multi Terrain Loaders [M0066672]
SERVICE EQUIPMENT AND SUPPLIES
SHIPPING GP
1.1. Shipping Weight

Choose an area for loading that is flat and stable.

  1. Secure the hydraulic lines to the backhoe. If caps are available, install the caps over the quick disconnect fittings. If caps are not available, connect the two fittings together.

  2. Refer to Operation and Maintenance Manual, "Lifting and Tying Down" for information on tying down the backhoe.

Shipping Weight

Use the following table to calculate the mass of your AVSpare work tool.

Table 1
Mass of the BH150 Backhoe  1053 kg (2321 lb) 
Mass of the BH160 Backhoe  1077 kg (2375 lb) 
Mass of the quick coupler  29 kg (63 lb) 
Mass of approved AVSpare work tools 
Digging Bucket size 304 mm (12 inch)  63 kg (139 lb) 
Digging Bucket size 406 mm (16 inch)  72 kg (159 lb) 
Digging Bucket size 457 mm (18 inch)  80 kg (176 lb) 
Digging Bucket size 508 mm (20 inch)  88 kg (194 lb) 
Digging Bucket size 609 mm (24 inch)  99 kg (218 lb) 
Digging Bucket size 762 mm (30 inch)  115 kg (254 lb) 
Ditch Cleaning Bucket size 1000 mm (39 inch)  110 kg (243 lb) 
Ditch Cleaning Bucket size 1200 mm (47 inch)  108 kg (238 lb) 
Ditch Cleaning Bucket size 1400 mm (55 inch)  121 kg (267 lb) 
Tilt Ditch Cleaning Bucket size 1200 mm (47 inch)  198 kg (437 lb) 
Flying Object Guard  11 kg (24 lb) 
A14B Auger  120 kg (265 lb) 
A19B Auger  93 kg (205 lb) 
6" Auger Bit  23 kg (50 lb) 
9" Auger Bit  34 kg (75 lb) 
12" Auger Bit  45 kg (100 lb) 
18" Auger Bit  65 kg (144 lb) 
24" Auger Tree Bit  74 kg (163 lb) 
24" Auger Bit  92 kg (203 lb) 
30" Auger Bit  126 kg (278 lb) 
36" Auger Bit  172 kg (379 lb) 
CVP16 Compactor Plate  215 kg (474 lb) 
Pin-On Mounting Bracket  38 kg (84 lb) 
Hydraulic Thumb  62 kg (137 lb) 

------ WARNING! ------

The 242A, 257A, and 259B3 maximum saleable weight machine, if used in combination with a BH150 Backhoe, a hydraulic hammer, and either a quick coupler, a thumb, or a full water tank, will exceed the maximum total machine rated capacity, which may result in personal injury or death. The mass of the machine and work tools should not exceed the mass on the ROPS film.


------ WARNING! ------

The 287B, 299C, and 299D XHP maximum saleable weight machine, if used in combination with a BH160 Backhoe, a hydraulic hammer, a quick coupler, a thumb, and a full water tank, will exceed the maximum total machine rated capacity, which may result in personal injury or death. The mass of the machine and work tools should not exceed the mass on the ROPS film.


Information System:

Improved Diesel Oxidation Catalyst (DOC) Is Used On Certain D Series Wheeled Excavators {1091}
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Control Valve
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Air Conditioner Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Air Conditioner Lines
340F Excavator Boom/Stick/Bucket Combinations
415F2 Industrial Loader Power Train Tire and Rim (Rear) - Remove and Install
340F Excavator Safety Messages
415F2 Industrial Loader Power Train Tire and Rim (Front) - Remove and Install
415F2 Industrial Loader Power Train Axle Housing (Service Brakes, Differential and Bevel Gear) - Assemble
415F2 Industrial Loader Power Train Axle Housing (Service Brakes, Differential and Bevel Gear) - Disassemble
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Condition Switch (Switch to Ground) - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Solenoid Return - Test
New K Series GET Adapters are Available on Certain Excavators and Wheel Loaders Buckets {6001, 6800, 6803}
C9 Engines for Caterpillar Built Machines Cylinder Head Valves
C9 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
349F XE and 352F XE Excavators Engine Oil Level - Check
New K Series GET Tips are Now Available for Certain Excavators and Wheel Loaders Buckets {6800, 6805}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Track
323F Excavator Maintenance Interval Schedule
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Idlers (Track)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Piston Motor (Propel)
An Improved Radiator is Now Used for Certain 300.9D, 301.4C, 302.7D CR Mini Hydraulic Excavators {1353, 1380}
Inspection and Rework Procedure for Swing Bearing Bolted Joint on Certain 305.5E and 306E Mini Hydraulic Excavators {7063}
Improved Electrical Grounding is Now Used on Certain 308E2 CR Mini Hydraulic Excavators {1408, 7301}