DFS118, DFS121 and DFS124 Silage Defacers Safety Messages Caterpillar


Safety Messages
`
DFS118, DFS121 and DFS124 Silage Defacers [M0068348]
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMS
DFS118, DFS121 and DFS124 Silage Defacers Safety Messages
1.1. Guard Removed (1)
2.1. Agitator (2)


Illustration 1g06052070
Typical Example

There are several specific safety messages on this work tool. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety messages.

Make sure that all of the safety signs are legible. Clean the safety signs or replace the safety signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety sign. Loose adhesive will allow the safety sign to fall. Replace any safety sign that is damaged or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Your AVSpare dealer can provide new safety signs.

Guard Removed (1)

This safety message is located on the top of the work tool.



Illustration 2g06029132

------ WARNING! ------

Do not place hand on or near work tool during operation. Work tool has rotating cutters. Entanglement could cause serious injury or death. Read the Operation and Maintenance Manual.


Agitator (2)

This safety message is located on the left side and on the right side of the work tool.



Illustration 3g06029126

------ WARNING! ------

Do not place hand on or near work tool during operation. Work tool has rotating cutters. Entanglement could cause serious injury or death. Read the Operation and Maintenance Manual.


Information System:

Installation of the <NOBR>487-5000</NOBR> Auxiliary Hydraulic Lines Gp on Certain Hydraulic Excavators {5057}
924K, 926M, 930K, 930M, 938K, and 938M Wheel Loaders Machine System Pilot Pressure - Check
307 Hydraulic Excavator Engine Supplement Refrigerant Compressor - Remove and Install
349F and 352F Excavators Monitoring System - Monitor with Installed Cat Grade With Assist
314F and 315F Excavators Machine System Specifications Chassis Lighting
An Improved Main Control Valve is Now Used on 308E2 CR and 308E2 SR Mini Hydraulic Excavators {5051}
314F and 315F Excavators Machine System Specifications Control Valve (Auxiliary)
349F and 352F Excavators Joystick Controls - Cat Grade With Assist System
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Window Wiper Motor - Remove and Install - Lower
336D 2L and 340D 2L Excavators Machine Systems Hydraulic Lockout Control - Remove and Install
352F Mobile Hydraulic Power Unit (MHPU) Machine System Main Hydraulic System
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Rotator Motor and Manifold - Remove and Install
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Rotator Motor and Manifold - Disassemble
314F and 315F Excavators Machine System Specifications Pilot Lines (Main Pump)
314F and 315F Excavators Machine System Specifications Swing Motor
314F and 315F Excavators Machine System Specifications Heater and Air Conditioner Mounting
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Hydraulic Rotator - Remove and Install
314F and 315F Excavators Machine System Specifications Pump Lines
314F and 315F Excavators Machine System Specifications Hydraulic Tank and Filter
314F and 315F Excavators Machine System Specifications Control Lines
314F and 315F Excavators Machine System Specifications Stick - 3.00 m (9.843 ft)
725C2 Articulated Truck Aftercooler Core - Inspect/Clean
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Engine Design