Tiltable Ditch Cleaning Buckets Safety Messages Caterpillar


Safety Messages
`
Tiltable Ditch Cleaning Buckets [M0068086]
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMS
Tiltable Ditch Cleaning Buckets Safety Messages
1.1. Crush Hazard (1)
2.1. Do Not Operate (2)


Illustration 1g06083821

There are several specific safety messages on this work tool. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety messages.

Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.

Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a new safety message on the replacement part. Any Cat dealer can provide new safety messages.

Crush Hazard (1)

This safety message is located on or near the rear of the work tool. Refer to your specific model.



Illustration 2g06032635

------ WARNING! ------

No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation.


Do Not Operate (2)

This safety message is located on or near the rear of the work tool. Refer to your specific model.



Illustration 3g06032632

------ WARNING! ------

Do not operate or work on this equipment unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any AVSpare dealer for replacement manuals. Proper care is your responsibility.


Information System:

GSV520 and GSV525 Orange Peel Grapples Hydraulic Cylinder - Assemble
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Determining Diagnostic Trouble Codes
329F and 330F Excavators Hydraulic System Auxiliary Pump Flow - Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Relief Valve (Pilot) - Test and Adjust
538 Forest Machine Machine Systems Engine Performance - Test - Engine Speed
325F Excavator Engine Supplement Refrigerant Condenser and Mounting - Remove and Install
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Cylinder Speed - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Cylinder Drift - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Travel on Level Ground - Test - Optional Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Travel on Level Ground - Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System Engine Performance - Test - Engine Speed
Tiltable Ditch Cleaning Buckets Work Tool Installation and Removal
A New Upper Frame Design is Now Used for Improved Magnet Cable Routing on Certain 320E Excavators {1408, 7051}
Installation Procedure for Front Mounted IT Quick Couplers on Certain 427F2, 428F2, and 434F2 Backhoe Loaders {6129}
336D 2L and 340D 2L Excavators Machine Systems Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Event Codes
558 Forest Machine Machine Systems Solenoid Valve (Proportional Reducing) - Calibrate - Power Shift Pressure
558 Forest Machine Machine Systems Relief Valve (Main) - Test and Adjust
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Differential
336D 2L and 340D 2L Excavators Machine Systems Main Control Valve - Remove and Install
538 Forest Machine Machine Systems Swing Motor - Test - Measurement of Case Drain Oil
Procedure for Reinforcing Bracket As on Certain M Series Motor Graders {6158, 6159}
Debris in Oil System Causing Repeat Failures of the (HEUI) Pump for Certain C7 and C9 Engines. {1126, 1251, 1318, 1378}