Horizontal Pin Lock Series PW Quick Coupler Safety Messages Caterpillar


Safety Messages
`
Horizontal Pin Lock Series PW Quick Coupler [SEBU7515]
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMS
Horizontal Pin Lock Series PW Quick Coupler Safety Messages
1.1. Do Not Operate (1)
2.1. Crush Point (2)


Illustration 1g03178027
Typical location of safety messages

There are several specific safety messages on this work tool. The exact location of the safety messages and the description of the safety messages are reviewed in this section. Become familiarized with all safety messages.

Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the safety messages if the illustrations are not legible. When you clean the safety messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.

Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any Cat dealer can provide new safety messages.

Do Not Operate (1)

This safety message is located on the side of the quick coupler.



Illustration 2g01206071

------ WARNING! ------

Do not operate or work on this machine or work tool unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals and Owner's Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility.


Crush Point (2)

This safety message is located on the side of the quick coupler.



Illustration 3g01368398

------ WARNING! ------

No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation.


Information System:

3500B Engines for 5130B and 5230B Excavators Electrical Connectors and Functions
Quick Coupler Wedge Lock(Wheel Loader) Safety Signs and Labels
312C Excavator 3064 Engine Supplement Water Pump - Install
312C Excavator 3064 Engine Supplement Water Pump - Remove
2001/07/30 Correctly Assembling the Buffer Seal Will Prevent Failure of the U-Cup Seals {7562}
3500B Engines Electronic Control Terms
5230B Excavator Electronic Systems Guide Vital Information Management System (VIMS)
3500B Engines for 5130B and 5230B Excavators System Overview
3064 and 3066 Engines for Caterpillar Built Machines Cooling System - Test
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
3064 and 3066 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3500B Engines for 5130B and 5230B Excavators Engine Misfires, Runs Rough or Is Unstable
312C Excavator 3064 Engine Supplement Water Separator - Remove and Install
305 CR Mini Hydraulic Excavator Monitoring System
W345B Series II Material Handler Hydraulic System Stick Hydraulic System
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Language Selection
5230B Excavator Hydraulic System Relief Valve (Main) - Test
312C Excavator 3064 Engine Supplement Air Conditioner Dryer - Remove and Install
W345B Series II Material Handler Hydraulic System Control Valve (Stick Lowering)
312C Excavator 3064 Engine Supplement Fuel Priming Pump - Remove and Install
3500B Engines for 5130B and 5230B Excavators Analog Sensor Supply
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Main Menu
312C Excavator 3064 Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install