5130B Excavator Pump Drive Oil - Change Caterpillar


Pump Drive Oil - Change
`
5130B Excavator [SEBU7071]
BASIC ENGINE
DRIVE GP-PUMP
5130B Excavator Pump Drive Oil - Change


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in AVSpare machines.

Dispose of all fluids according to local regulations and mandates.





Illustration 1g00656389

Ecology drain valve (3) for the pump drive oil is located under the center of the upper structure on the right side.

    Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing fluid spillage.

  1. Remove oil drain plug (3) .

  1. The oil drain hose is located in the toolbox. Place the end of the oil drain hose into a suitable oil container.

  1. Screw the hose fitting onto the ecology drain valve. The oil drain hose opens the valve and the oil drains.

  1. Remove the oil drain hose and reinstall the oil drain plug.



    Illustration 2g00656390

  1. Dipstick (1) and filler cap (2) are located in the right rear corner of the hydraulic pump room. Remove dipstick (1) and remove filler cap (2) .

  1. Add the correct quantity of oil through the fill port. Refer to Operation and Maintenance Manual, "Lubricant Viscosities" and Operation and Maintenance Manual, "Capacities (Refill)" for the correct type of oil and volume of oil.



    Illustration 3g00665940

  1. Maintain the oil level between the marks on dipstick (1) .

  1. Clean filler cap (2). Inspect the O-ring. Replace the O-ring if the O-ring is worn or damaged.

  1. Reinstall the filler cap and reinstall the dipstick.

  1. Inspect the drained oil for metal chips or particles. If you find any chips or particles, contact your AVSpare dealer.

  1. Dispose of drained oil according to local regulations.

Information System:

C9.3 Engines for Caterpillar Built Machines Electrical System
5230B Excavator Machine Systems Pilot Valve (Travel) - Remove
305 CR Mini Hydraulic Excavator Window Wiper and Washer Control - If Equipped
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Plate Locations and Film Locations
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Boom/Stick/Bucket Combinations
3500B Engines for 5130B and 5230B Excavators Electrical Power Supply
325C L and 325C LN Excavator Lifting Capacities Lifting Capacities - 325C Excavator
305 CR Mini Hydraulic Excavator Light Switches
M325B Material Handler Machine Systems Boom Cylinder - Assemble
W345B Series II Material Handler Hydraulic System Control Valve (Boom Lowering)
5230B Excavator Machine Systems Gear Pump (Pump Drive Lubrication) - Assemble
M325B Material Handler Machine Systems Boom Cylinder - Disassemble
3126B Engine for Caterpillar Built Machines Engine Fan Control Solenoid Circuit - Test
2001/09/17 Correction to Serial Numbers for "Alternator Debris Guard Available" {1405}
3126B Engines Fuel System - Inspect
5130B Excavator Automatic Lubrication System Grease - Add
3500B Engines for 5130B and 5230B Excavators Ether Injection System
305 CR Mini Hydraulic Excavator Window (Front) - If Equipped
5230B Excavator Hydraulic System Solenoid Valves (Pilot Manifold)
3500B Engines for 5130B and 5230B Excavators Ground Level Shutdown Switch
C15 Petroleum Generator Set Engines Electronic Unit Injector - Adjust
3064 and 3066 Engines for Caterpillar Built Machines Camshaft - Remove
3064 and 3066 Engines for Caterpillar Built Machines Camshaft Bearings - Remove
5130B Excavator Swing Drive Oil - Change