M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom Caterpillar


Lifting Capacities - M318C Excavator with a One-Piece Boom
`

Note: These lifting capacity tables are for typical options.

Note: For more information on your specific configuration, see your dealer.

Note: The lifting capacities in the following tables represent the maximum lifting capacities. Each machine is configured differently. The following options require additional tables for lifting capacities:

  • Optional buckets

  • Optional sticks

  • Quick coupler

The following conditions affect the lifting capacities:

(A) - The rear dozer is up.

(B) - The rear dozer is down. The lifting capacity is over the rear.

(C) - The rear stabilizers are down. The lifting capacity is over the rear.

(D) - The front and rear stabilizers are down.

(E) - The rear dozer and front stabilizers are down.

(F) - Front Load

(S) - Side Load

Table 1
M318C Excavator with a One-Piece Boom,
2.8 m (9.2 ft) stick and a 0.70 m3 bucket
Metric Tons    
Radius     3.0 m     4.5 m     6.0 m     7.5 m     Maximum Reach    
Load Point Height     F     S     F     S     F     S     F     S     F     S     m    
6.0 m     A                     4.2 (1)     2.9                        
B                 3.3                
C                 4.0                
D                 4.2 (1)                
E                            
4.5 m     A                     4.6     2.8     3.1     1.8                
B                 4.7 (1)     3.2     3.6 (1)     2.1            
C                 3.9 2.6        
D                 4.7 (1) 3.6 (1)        
E                 3.2        
3.0 m     A             7.0 (1)     4.2     4.4     2.7     3.0     1.8     1.5 (1)     1.2     9.12    
B         4.9 5.4 (1)     3.1     4.6 (1)     2.0     1.5
C         6.0 3.8 4.3     2.5     1.5 (1)
D         7.0 (1) 5.4 (1) 4.6 (1)     3.8    
E         4.6 3.1
1.5 m     A             6.6     3.8     4.2     2.5     2.9     1.7     1.6 (1)     1.1     9.35    
B         8.5 (1)     4.4     6.1 (1)     2.9     4.7     2.0     1.3
C         5.5 3.5 4.2     2.5     1.6 (1)
D         8.5 (1) 5.4 4.8 (1)     3.7    
E         6.9 4.4 3.0
0.0 m     A     4.4 (1)     6.3     3.5     4.0     2.3     2.8     1.6     1.7 (1)     1.1     9.28    
B 9.1 (1) 4.1 6.5 (1)     2.7     4.6     1.9     1.3    
C 5.2 6.0     3.4     4.1     2.4     1.7
D 8.2 6.5 (1)     5.2     5.0 (1)     3.6     1.7 (1)
E 6.6 4.2 3.0
-1.5 m     A     7.5 (1)     6.4     6.2     3.4     4.0     2.2     2.8     1.6     1.9 (1)     1.2     8.92    
B 7.5 (1) 8.8 (1)     4.0     6.4 (1)     2.6     4.6     1.8     1.4    
C 5.1 5.9     3.3     4.1     2.3     1.8
D 8.1 6.4 (1)     5.1     4.7 (1)     3.6     1.9 (1)
E 6.5 4.1 2.9
-3.0 m     A     11.0 (1)     6.6     6.3     3.5     4.0     2.2             2.3 (1)     1.4     8.22    
B 7.9 7.7 (1)     4.1     5.5 (1)     2.6             1.6
C 10.3 5.2 3.3         2.1
D 11.0 (1) 7.7 (2) 5.1         2.3 (1)
E 6.5 4.1        
-4.5 m     A     7.5 (1)     6.9     5.3 (1)     3.6                                
B 7.5 (1) 4.3                                
C 5.3 (1)                            
D                
E                
( 1 ) Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.

Information System:

325C and 325C L Excavator Leaving the Machine
305 CR Mini Hydraulic Excavator Hydraulic System Cylinder Drift - Check
312C Excavator Machine Systems Main Hydraulic Pump - Remove
W345B Series II Material Handler Hydraulic System Speed Reducer
3500B Engines for 5130B and 5230B Excavators E021 High Exhaust Temperature Derate
305 CR Mini Hydraulic Excavator Hydraulic System Engine Performance - Test - Engine Speed
5230B Excavator Machine Electronic Control System Switches
312C Excavator Machine Systems Pilot Valve (Oil Manifold) - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators Rectifier - Test
H45/H45S, H50/H50S, 63/H63/H63S, 70/70S/H70/H70S, H90C/H90CS and 100/H100/H100S Hydraulic Hammers Tool Bushing (Upper) - Inspect/Replace - H90C/H90Cs and H100/H100s Only
305 CR Mini Hydraulic Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
305.5 Mini Hydraulic Excavator Travel Control
5230B Excavator Hydraulic System Travel Parking Brake
H115/H115S, H120/H120CS, H130/H130S, H140/H140S, H160/H160S, H180/H180S, and H195 Hydraulic Hammers Approved Machines
305 CR Mini Hydraulic Excavator Hydraulic System Cylinder Speed - Check
3500B Engines for 5130B and 5230B Excavators E039 Low Engine Oil Pressure Derate
3064 and 3066 Engines for Caterpillar Built Machines Engine Speed - Check
305 CR Mini Hydraulic Excavator Hydraulic System Travel on Level Ground - Test
5230B Excavator Machine Systems Pilot Valve (Implement) - Remove
305 CR Mini Hydraulic Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
305 CR Mini Hydraulic Excavator Hydraulic System Machine Drift on a Slope - Check
305 CR Mini Hydraulic Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
305 CR Mini Hydraulic Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
W345B Series II Material Handler Hydraulic System Travel Hydraulic System