M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom Caterpillar


Lifting Capacities - M318C Excavator with a One-Piece Boom
`

Note: These lifting capacity tables are for typical options.

Note: For more information on your specific configuration, see your dealer.

Note: The lifting capacities in the following tables represent the maximum lifting capacities. Each machine is configured differently. The following options require additional tables for lifting capacities:

  • Optional buckets

  • Optional sticks

  • Quick coupler

The following conditions affect the lifting capacities:

(A) - The rear dozer is up.

(B) - The rear dozer is down. The lifting capacity is over the rear.

(C) - The rear stabilizers are down. The lifting capacity is over the rear.

(D) - The front and rear stabilizers are down.

(E) - The rear dozer and front stabilizers are down.

(F) - Front Load

(S) - Side Load

Table 1
M318C Excavator with a One-Piece Boom,
2.5 m (8.2 ft) stick and 0.80 m3 bucket
Metric Tons    
Radius     3.0 m     4.5 m     6.0 m     7.5 m     Maximum Reach    
Load Point Height     F     S     F     S     F     S     F     S     F     S     m    
6.0 m     A                     4.6 (1)     2.9                        
B                 3.3                
C                 4.0                
D                 4.6 (1)                
E                            
4.5 m     A                     4.6     2.8     3.0     1.8                
B                 4.9 (1)     3.2     3.3 (1)     2.1            
C                 3.9 2.6        
D                 4.9 (1) 3.3 (1)        
E                 4.7 3.2        
3.0 m     A             7.0     4.2     4.4     2.6     3.0     1.7     1.7 (1)     1.3     8.83    
B         7.4     4.8     5.6 (1)     3.0     4.7 (1)     2.0     1.5
C         5.9 3.7 4.3     2.5     1.7 (1)
D         7.4 (1) 5.5 4.7 (1)     3.8    
E         7.3 4.6 3.1
1.5 m     A             6.6     3.7     4.2     2.4     2.9     1.6     1.8 (1)     1.2     9.06    
B         8.7 (1)     4.4     6.2 (1)     2.8     4.7     1.9     1.4
C         5.5 6.1     3.5     4.2     2.4     1.8 (1)
D         8.5 6.2 (1)     5.3     4.9 (1)     3.7    
E         6.8 4.3 3.0
0.0 m     A             6.3     3.5     4.0     2.3     2.8     1.6     1.9 (1)     1.2     9.00    
B         9.1 (1)     4.1     6.5 (1)     2.7     4.6     1.9     1.4
C         5.2 5.9     3.4     4.1     2.4     1.8
D         8.2 6.5 (1)     5.2     4.9 (1)     3.6     1.9 (1)
E         6.5 4.2 3.0
-1.5 m     A     7.8 (1)     6.5     6.2     3.4     4.0     2.2             2.2 (1)     1.2     8.62    
B 7.8 8.7 (1)     4.1     6.3 (1)     2.6             1.5    
C 7.8 (1) 5.1 5.9     3.3             1.9
D 8.1 6.3 (1)     5.1             2.2 (1)
E 6.5 4.1        
-3.0 m     A     10.3 (1)     6.7     6.3     3.5     4.0     2.3             2.6 (1)     1.5     7.89    
B 8.0 7.4 (1)     4.1     5.2 (1)     2.7             1.7
C 10.3 (1) 5.2 3.3         2.2
D 7.4 (2) 5.1         2.6 (1)
E 6.5 4.2        
-4.5 m     A             4.5 (1)     3.7                                
B         4.3                            
C         4.5 (1)                            
D                            
E                            
( 1 ) Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.

Information System:

305 CR Mini Hydraulic Excavator Hydraulic System Specifications
5230B Excavator Machine Electronic Control System Sensors
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom
305 CR Mini Hydraulic Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom
3500B Engines for 5130B and 5230B Excavators E095 Fuel Filter Restriction Warning
325C and 325C L Excavator Boom/Stick/Bucket Combinations
3524B Engines for Off-Highway Trucks E072 Oil Level Low Mark
W345B Series II Material Handler Hydraulic System Travel Hydraulic System
305 CR Mini Hydraulic Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
305 CR Mini Hydraulic Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
305 CR Mini Hydraulic Excavator Hydraulic System Machine Drift on a Slope - Check
Installation Instructions for the 174-1508 Electric Motor {5927}
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
5230B Excavator Machine Systems Control Valve (Swing) - Assemble
305 CR Mini Hydraulic Excavator Hydraulic Lockout Control
325C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
325C Excavator Hydraulic System Operational Checks
5230B Excavator Machine Systems Control Valve (Swing) - Disassemble
325C Excavator Hydraulic System Engine Performance - Test - Engine Speed
5130B Excavator Sampling Interval and Location of Sampling Valve
325D and 329D Excavators Hydraulic System Travel on Level Ground - Test
325C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
325D and 329D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check