5130B Excavator Sampling Interval and Location of Sampling Valve Caterpillar


Sampling Interval and Location of Sampling Valve
`
5130B Excavator [SEBU7071]
HYDRAULIC SYSTEM
5130B Excavator Sampling Interval and Location of Sampling Valve

Take the oil samples as close as possible to the standard intervals. In order to receive the full value from Scheduled Oil Sampling (S·O·S) oil analysis, you must establish a consistent trend of data. In order to establish a pertinent history of data, perform consistent samplings that are evenly spaced.

Table 1
Component or System     Oil Change Interval     Sampling Interval     Sampling Valve    
Engine     Every 500 Hours     Every 250 Hours     Yes    
Hydraulics     Every 2000 Hours     Every 250 Hours     Yes    
Pump Drive     Every 1000 Hours     Every 250 Hours     Yes    
Final Drives     Every 1000 Hours     Every 250 Hours     No    
Swing Drives     Every 1000 Hours     Every 250 Hours     No    



Illustration 1g00816869

Location of sampling valve (1) for the engine oil

Sampling valve (1) for the engine oil is located to the right of the engine oil filters.




Illustration 2g00816886

Location of sampling valve (2) for the hydraulic oil

Sampling valve (2) for the hydraulic oil is located on the front of the hydraulic tank in the center of the manifold.




Illustration 3g00658284

Location of sampling valve (3) for the pump drive oil

Sampling valve (3) is located in the pump room above the top pump.




Illustration 4g00816956

Location of filler plug (4) for the final drive

Filler plug (4) is located on the cover for the final drive.




Illustration 5g00816937

Location of dipstick (5) for the swing drive

Dipstick (5) is located on each swing drive motor.

Consult your AVSpare dealer for complete information and assistance in establishing a Scheduled Oil Sampling (S·O·S) program for your equipment.

Information System:

325C Excavator Hydraulic System Engine Performance - Test - Engine Speed
5230B Excavator Machine Systems Control Valve (Swing) - Disassemble
325C Excavator Hydraulic System Operational Checks
325C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
305 CR Mini Hydraulic Excavator Hydraulic Lockout Control
5230B Excavator Machine Systems Control Valve (Swing) - Assemble
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
Installation Instructions for the 174-1508 Electric Motor {5927}
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
305 CR Mini Hydraulic Excavator Hydraulic System Specifications
5230B Excavator Machine Electronic Control System Sensors
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom
325D and 329D Excavators Hydraulic System Travel on Level Ground - Test
325C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
325D and 329D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
325D and 329D Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
325C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
325D and 329D Excavators Hydraulic System Cylinder Speed - Check
325C Excavator Hydraulic System Specifications
312C Excavator Machine Systems Main Hydraulic Pump - Install
325C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust
325C Excavator Specifications