325C Excavator Specifications Caterpillar


Specifications
`
1.1. Intended Use
2.1. Specification Data

Basic machine specifications are listed below.

Intended Use

The intended use of this machine is for excavating with a bucket or working with approved work tools. Without moving the undercarriage during the work cycle, the upper structure is normally capable of a 360 degree swing with mounted equipment. This machine can be used in object handling applications with approved lifting points and with approved lifting devices.

Specification Data




Illustration 1g00880203

Table 1
325C L Excavator (1)    
Approximate Weight    
28400 kg (62611 lb)    
Overall Length (A)    
10340 mm (33 ft 11.1 inch)    
Overall Height (B)    
3320 mm (10 ft 10.7 inch)    
Height of Cab (C)    
3040 mm (9 ft 11.7 inch)    
Overall Width (D)    
3390 mm (11 ft 1.5 inch)    
Track Shoe Width (E)    
800 mm (2 ft 7.5 inch)    
( 1 ) These specifications are for a machine that has a 6.15 m (20 ft 2 inch) boom, a 3.2 m (10 ft 6 inch) stick, a 1.2 m3 (1.3 yd3 ) bucket, and a 10 percent full fuel tank.

Table 2
325C LN Excavator (1)    
Approximate Weight    
28000 kg (61729.3600 lb)    
Overall Length (A)    
10340 mm (33 ft 11.1 inch)    
Overall Height (B)    
3320 mm (10 ft 2.8 inch)    
Height of Cab (C)    
3040 mm (9 ft 11.7 inch)    
Overall Width (D)    
2990 mm (9 ft 9.7 inch)    
Track Shoe Width (E)    
600 mm (2 ft)    
( 1 ) These specifications are for a machine that has a 6.15 m (20 ft 2 inch) boom, a 3.2 m (10 ft 6 inch) stick, a 1.1 m3 (1.2 yd3) bucket, and a 10 percent full fuel tank.

Information System:

325C Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
312C Excavator Machine Systems Main Hydraulic Pump - Install
325C Excavator Hydraulic System Specifications
325D and 329D Excavators Hydraulic System Cylinder Speed - Check
325C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
325D and 329D Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
325D and 329D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
325C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
325D and 329D Excavators Hydraulic System Travel on Level Ground - Test
5130B Excavator Sampling Interval and Location of Sampling Valve
325C Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
W345B Series II Material Handler Hydraulic System Travel Motor
305.5 Mini Hydraulic Excavator Machine System Specifications Main Control Valve
325C Excavator Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom
312C Excavator 3064 Engine Supplement Engine - Remove
5230B Excavator Machine Systems Swivel - Disassemble
325C Excavator Hydraulic System Pump Control (Output Flow) - Adjust
325C Excavator Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
2001/09/10 Special Instruction, REHS0932, "Procedure to Rework the Return Lines for the Margin Relief Valve" Lists Two Incorrect Part Numbers {0374, 5057, 5069}
5130B Excavator Cooling System Coolant (ELC) - Change
325C Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil