M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom Caterpillar

Lifting Capacities - M318C Excavator with a VA Boom

M316C, M318C and M322C Excavators and M318C and M322C Material Handlers [SEBU7430]

M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom

M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Shipping the Machine

MACHINE ARRANGEMENT

322B, 322B L, 325B and 325B L Excavators Operation

M318 and M320 Excavators Boom, Stick and Bucket Operation

M318 and M320 Excavators Clamshell Operation

584 and 584HD Forwarders General Hazard Information

Note: These lifting capacity tables are for typical options.

Note: For more information on your specific configuration, see your dealer.

Note: The lifting capacities in the following tables represent the maximum lifting capacities. Each machine is configured differently. The following options require additional tables for lifting capacities:

Optional buckets
Optional sticks
Quick coupler

The following conditions affect the lifting capacities:

(A) - The rear dozer is up.

(B) - The rear dozer is down. The lifting capacity is over the rear.

(C) - The rear stabilizers are down. The lifting capacity is over the rear.

(D) - The front and rear stabilizers are down.

(E) - The rear dozer and front stabilizers are down.

(F) - Front Load

(S) - Side Load

Show/hide table

Table 1
M318C Excavator with a VA Boom, 2.2 m (7.2 ft) stick and 0.90 m³ bucket Metric Tons
Radius		3.0 m		4.5 m		6.0 m		7.5 m		Maximum Reach
Load Point Height		F	S	F	S	F	S	F	S	F	S	m
6.0 m	A			5.5 ⁽¹⁾	4.8	4.6	2.8
	B				5.4	5.0 ⁽¹⁾	3.2
	C				5.5 ⁽¹⁾		3.9
	D						5.0 ⁽¹⁾
	E						4.8
4.5 m	A			6.4 ⁽¹⁾	4.6	4.6 ⁽¹⁾	2.9
	B				5.3	5.2 ⁽¹⁾	3.3
	C				6.3		4.0
	D				6.4		5.2 ⁽¹⁾
	E				6.4		4.8
3.0 m	A	8.7 ⁽¹⁾	8.4	7.1	4.5	4.6	2.9	3.0	1.7	2.0 ⁽¹⁾	1.4	8.48
	B		8.7 ⁽¹⁾	7.7 ⁽¹⁾	5.1	5.8 ⁽¹⁾	3.3	4.8 ⁽¹⁾	2.0		1.6
	C				6.1 ⁽¹⁾		4.0	4.3	2.5		2.0 ⁽¹⁾
	D				7.7 ⁽¹⁾		5.6	4.8 ⁽¹⁾	3.8
	E				7.3		4.7	4.8 ⁽¹⁾	3.1
1.5 m	A	11.4 ⁽¹⁾	8.2	7.0	4.4	4.6	2.8	2.9	1.6	2.1 ⁽¹⁾	1.2	8.73
	B		9.4	8.8 ⁽¹⁾	5.1	6.3 ⁽¹⁾	3.2	4.7	1.9		1.5
	C		11.4 ⁽¹⁾		6.1	6.2	3.9	4.2	2.4		1.9
	D				8.6 ⁽¹⁾	6.3 ⁽¹⁾	5.5	4.9 ⁽¹⁾	3.7		2.1 ⁽¹⁾
	E				7.2 ⁽¹⁾	6.3 ⁽¹⁾	4.7	4.9 ⁽¹⁾	3.0		2.1 ⁽¹⁾
0.0 m	A	13.5 ⁽¹⁾	7.9	7.1	4.3	4.4	2.6	2.8	1.5	2.2	1.2	8.66
	B		9.3	9.0 ⁽¹⁾	4.9	6.4 ⁽¹⁾	3.0	4.7	1.8	2.3 ⁽¹⁾	1.4
	C		11.6 ⁽¹⁾		6.1	6.2 ⁽¹⁾	3.7	4.1	2.3		1.9
	D		13.5 ⁽¹⁾		8.6 ⁽¹⁾	6.4 ⁽¹⁾	5.6	4.7 ⁽¹⁾	3.6		2.3 ⁽¹⁾
	E		13.5 ⁽¹⁾		7.3	6.4 ⁽¹⁾	4.6	4.7 ⁽¹⁾	2.9		2.3 ⁽¹⁾
-1.5 m	A	14.3	7.6	7.0	4.1	4.2	2.4			2.4	1.3	8.27
	B	14.9 ⁽¹⁾	9.0	9.2 ⁽¹⁾	4.7	6.6 ⁽¹⁾	2.8			2.6 ⁽¹⁾	1.5
	C		11.5		5.9	6.2	3.5				2.0
	D		14.9 ⁽¹⁾		8.9 ⁽¹⁾	6.6 ⁽¹⁾	5.4				2.6 ⁽¹⁾
	E		14.6		7.3	6.6 ⁽¹⁾	4.4				2.5
-3.0 m	A	14.5	7.6	6.7	3.8	4.1	2.3
	B	15.4 ⁽¹⁾	9.0	9.0 ⁽¹⁾	4.5	4.5 ⁽¹⁾	2.7
	C		11.5		5.6		3.4
	D		15.4 ⁽¹⁾		8.7		4.5 ⁽¹⁾
	E		15.0		7.0		4.2

Show/hide table

^( 1 )

Capacity is limited by hydraulics rather than by a tipping load. The loads do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.