Boom and Stick Linkage - Lubricate
`
305 CR Mini Hydraulic Excavator
[SEBU7428]
305 CR Mini Hydraulic Excavator
Belt - Inspect/Adjust/Replace
305 CR Mini Hydraulic Excavator
Cooling System Coolant (ELC) - Change
IMPLEMENTS
BOOM GP
305 CR Mini Hydraulic Excavator
Boom and Stick Linkage - Lubricate
305 CR Mini Hydraulic Excavator
Boom/Stick/Bucket Combinations
Note: AVSpare recommends the use of 5P-0960 Molybdenum Grease for lubricating the boom, stick and bucket control linkage. Refer to Special Publication, SEBU6250, "AVSpare Machine Fluids Recommendations" for more information on molybdenum grease.
Apply lubricant through all fittings after operation under water.
Wipe all fittings before you apply lubricant.
- Apply lubricant through the fittings at the swing post.
Show/hide table
Illustration 2 g00823727 - Apply lubricant through the fitting at the base of the boom.
Show/hide table
Illustration 3 g00823729 - Apply lubricant through the fitting at the boom cylinder head end.
Show/hide table
Illustration 4 g00823733 - Apply lubricant through the fitting at the rod end of the boom cylinder.
Show/hide table
Illustration 5 g00823737 - Apply lubricant through the fitting at the stick cylinder head.
Show/hide table
Illustration 6 g00823741 - Apply lubricant through the following fittings:
- (1) The fitting that is located between the boom and the stick.
- (2) The fitting that is located at the stick cylinder rod end.
- (3) The fitting that is located at the bucket cylinder head end.
Show/hide tableIllustration 7 g00823748 - Apply lubricant through the following fittings:
- (4) The fitting that is located at the swing cylinder head end.
- (5) The fitting that is located at the swing cylinder rod end.
Show/hide table
![]() | |
Illustration 1 | g00823721 |
Information System:
416C, 426C, 428C, 436C and 438C Backhoe Loaders
Quick Coupler Operation (Backhoe) - Pin Grabber Quick Coupler (If Equipped)
420D and 430D Backhoe Loaders
Quick Coupler Operation (Loader)
420D and 430D Backhoe Loaders
Quick Coupler Control (Loader) - If Equipped
2001/10/15
A Correction to Spacers for Installing Tire Chains on the Rear Wheels of Backhoe Loaders Are Now Available {3259, 3278, 4201}
305 CR Mini Hydraulic Excavator
Belt - Inspect/Adjust/Replace
312C and 312C L Excavator
Plate Locations and Film Locations
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders
Sound Information and Vibration Information
330B Excavator Machine System Specifications
Track Carrier Roller
305 CR Mini Hydraulic Excavator
Capacities (Refill)
HDB Series and M1 Series Heavy Duty Brushless Alternators
Alternator - Disassemble - HDB Series Alternator
312C Excavator Machine Systems
Tank and Filter (Hydraulic) - Remove
305 CR Mini Hydraulic Excavator
Access Door and Cover Locations
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers
Lubricant Viscosities
432D and 442D Backhoe Loaders
Equipment Lowering with Engine Stopped
305.5 Mini Hydraulic Excavator
Bucket Tips - Inspect/Replace
345B Series II Excavator Hydraulic System
Main Control Valve
Horizontal Pin Lock Series PW Quick Coupler
Rated Load
305 CR Mini Hydraulic Excavator
Cooling System Coolant (ELC) - Change
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Real Time Error Codes
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Troubleshooting Undiagnosed Problems
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Parameter - Adjust
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Hydraulic Hammer - Adjust
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Engine Speed Dial Setting - Check
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Digital Output On/Off - Test