MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations Caterpillar


Plate Locations and Film Locations
`
MP15, MP20, MP30 and MP40 Multi-Processors [SEBU7750]
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMS
MP15, MP20, MP30 and MP40 Multi-Processors Safety Messages
MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations
1.1. European Union
2.2. Information for Frame
3.2. Information for Jaw Sets
4.2. CE Mark

AVSpare work tools are identified by Serial Numbers.

The serial number plate (1) is located on the side of the frame near the rotator.



Illustration 1g02144836
(1) Typical example of serial number plate on frame


Illustration 2g01444045
(1) Typical example of serial number plate and CE mark on frame

AVSpare Multi-processor jaw sets are identified by Serial Numbers.

The serial number plate (2) is located on the moveable jaw of the jaw set near the hinge point.



Illustration 3g02144859
(2) Typical example of serial number plate on jaw set


Illustration 4g02152842
(2) Typical example of serial number plate on jaw set

European Union

For work tools that are compliant to "2006/42/EC", the following information is stamped onto the serial number CE plate.

Information for Frame

For quick reference, record the identification numbers in the spaces that are provided below for the frame.

Model Number____________________

Serial Number____________________

Year of Manufacture____________________

Mass (kg)____________________

Information for Jaw Sets

For quick reference, record the identification numbers in the spaces that are provided below for the jaw set.

Model Number____________________

Serial Number____________________

Year of Manufacture____________________

Mass (kg)____________________

For quick reference, record the identification numbers in the spaces that are provided below for a second jaw set.

Model Number____________________

Serial Number____________________

Year of Manufacture____________________

Mass (kg)____________________

CE Mark

The CE mark is located on the serial number plate (1).

Information System:

Installation of the 300-1190 Auxiliary Hydraulic Lines Gp {5057}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Condenser - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Crossover) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Refrigerant Receiver-Dryer - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Compressor - Remove and Install
2010/04/28 Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM 3G Electrical Connector - Inspect
568 Forest Machine Hydraulic System Swing Speed and Overswing on Level Ground - Check
568 Forest Machine Hydraulic System Travel on Level Ground - Test - Optional Test
568 Forest Machine Hydraulic System Travel on Level Ground - Test
568 Forest Machine Hydraulic System Operational Checks
330D and 336D Excavators and 336D Mobile Hydraulic Power Units Maintenance Interval Schedule
349E Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
374D Excavator Machine System Specifications Boom - 7.00 m (23.0 ft)
374D Excavator Machine System Specifications Stick - 2.57 m (8.432 ft)
374D Excavator Machine System Specifications Stick - 3.60 m (11.8 ft)
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Oil Pan - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Daily Inspection
MP15, MP20, MP30 and MP40 Multi-Processors Declaration of Conformity
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Passive) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Work Tool Installation and Removal
2010/04/15 A New Torque Is Used for Installing the Check Valve Gp into the Secondary Fuel Filter Base on Certain Machine Engines {1261, 1274, 5067}
349F and 352F Excavators Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage Bearings and Seals - Remove and Install