MP15, MP20, MP30 and MP40 Multi-Processors Daily Inspection Caterpillar


Daily Inspection
`

------ WARNING! ------

Personal injury or death can result from improperly checking for a leak.

Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.

If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.



NOTICE

Accumulated grease and oil on a work tool is a fire hazard.

Remove debris with steam cleaning or high pressure water at any time a significant quantity of oil is spilled on the work tool.


Note: If major repairs to the work tool are required, consult your AVSpare dealer.

  1. For the maximum service life of the work tool, make a thorough daily inspection before you mount the work tool and before you start the engine.

  2. Inspect the work tool for the following conditions: loose bolts, worn cutters, worn teeth, oil leaks, worn parts and broken parts. Inspect the work tool for missing parts. Check the overall condition of the work tool. Check the overall condition of the hydraulic system.

  3. Inspect the condition of the hydraulic lines and the hydraulic fittings.

  4. Inspect the cutting jaw. Remove scrap and debris from the jaw.

  5. Inspect the welds, the pins, and the bores for damage. If the components are damaged, consult your AVSpare dealer.

  6. Visually inspect the rotator head bolts. If any rotator head bolts are missing or damaged, replace all the bolts.

    Reference: For more information on inspecting the rotator head bolts, refer to Operation and Maintenance Manual, "Rotator Head Bolts - Inspect".

    Reference: Contact your AVSpare dealer for replacement of the rotator head bolts.

  7. Perform all repairs before the work tool is put into service.

  8. Check the hydraulic oil. Maintain the oil to the proper level. Refer to the Operation and Maintenance Manual for the host machine.

  9. Visually inspect the bracket bolts. If any bracket bolts are damaged or missing, replace all the bracket bolts.

Information System:

336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Oil Pan - Remove and Install
374D Excavator Machine System Specifications Stick - 3.60 m (11.8 ft)
374D Excavator Machine System Specifications Stick - 2.57 m (8.432 ft)
374D Excavator Machine System Specifications Boom - 7.00 m (23.0 ft)
349E Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations
Installation of the 300-1190 Auxiliary Hydraulic Lines Gp {5057}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Condenser - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Crossover) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Refrigerant Receiver-Dryer - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Compressor - Remove and Install
2010/04/28 Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307}
MP15, MP20, MP30 and MP40 Multi-Processors Declaration of Conformity
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Passive) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Work Tool Installation and Removal
2010/04/15 A New Torque Is Used for Installing the Check Valve Gp into the Secondary Fuel Filter Base on Certain Machine Engines {1261, 1274, 5067}
349F and 352F Excavators Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage Bearings and Seals - Remove and Install
Procedure to Repair The Welds on Certain Excavators Track Roller and Car Body Frames{0679, 4150, 4151, 7062}
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
374D Excavator Machine System Specifications Boom Cylinder
374D Excavator Machine System Specifications Bucket Cylinder
374D Excavator Machine System Specifications Bucket Cylinder
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Engine Front Mount - Remove and Install