MP15, MP20, MP30 and MP40 Multi-Processors Declaration of Conformity Caterpillar


Declaration of Conformity
`
MP15, MP20, MP30 and MP40 Multi-Processors [SEBU7750]
MACHINE ARRANGEMENT
MP15, MP20, MP30 and MP40 Multi-Processors Declaration of Conformity

Table 1
An EC or EU Declaration of Conformity document was provided with the machine if it was manufactured to comply with specific requirements for the European Union. In order to determine the details of the applicable Directives, review the complete EC or EU Declaration of Conformity provided with the machine. The extract shown below from an EC or EU Declaration of Conformity for machines that are declared compliant to 2006/42/EC applies only to those machines originally CE marked by the manufacturer listed and which have not since been modified. 
 
ORIGINAL EC or EU DECLARATION OF CONFORMITY 
 
Manufacturer:
AVSpare Work Tools B.V.
Sigarenmakerstraat 9
NL-5232 BJ 's-Hertogenbosch,
The Netherlands 
Person authorized to compile the Technical File and to communicate relevant part (s) of the Technical File to the Authorities of European Union Member States on request: 
  Standards & Regulations Manager, AVSpare France S.A.S 40,
Avenue Leon-Blum, B.P. 55, 38041 Grenoble Cedex 9, France 
I, the undersigned, _________, hereby certify that the construction equipment specified hereunder 
Description:  Generic Denomination:  Earth-moving Equipment   
  Function:  Multi-processor     
  Model/Type:  MP15, MP20, MP30, and MP40 Multi-Processors     
  Serial Number:       
  Commercial Name:  AVSpare Inc.     
Fulfills all the relevant provisions of the following Directives   
             
  Directives  Notified Body  Document No.   
  2006/42/EC  N/A     
  2014/30/EU  N/A     
         
         
             
     
           
     
Done at:      Signature     
Date:      Name/Position     
             
Note: The above information was correct as of April 2010, but may be subject to change, please refer to the individual declaration of conformity issued with the machine for exact details. 

Information System:

MP15, MP20, MP30 and MP40 Multi-Processors Daily Inspection
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Oil Pan - Remove and Install
374D Excavator Machine System Specifications Stick - 3.60 m (11.8 ft)
374D Excavator Machine System Specifications Stick - 2.57 m (8.432 ft)
374D Excavator Machine System Specifications Boom - 7.00 m (23.0 ft)
349E Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations
Installation of the 300-1190 Auxiliary Hydraulic Lines Gp {5057}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Condenser - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Crossover) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Refrigerant Receiver-Dryer - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Compressor - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Passive) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Work Tool Installation and Removal
2010/04/15 A New Torque Is Used for Installing the Check Valve Gp into the Secondary Fuel Filter Base on Certain Machine Engines {1261, 1274, 5067}
349F and 352F Excavators Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage Bearings and Seals - Remove and Install
Procedure to Repair The Welds on Certain Excavators Track Roller and Car Body Frames{0679, 4150, 4151, 7062}
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
374D Excavator Machine System Specifications Boom Cylinder
374D Excavator Machine System Specifications Bucket Cylinder
374D Excavator Machine System Specifications Bucket Cylinder
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Engine Front Mount - Remove and Install
374D Excavator Machine System Specifications Bucket Cylinder