MP15, MP20, MP30 and MP40 Multi-Processors Transport Position Caterpillar


Transport Position
`
MP15, MP20, MP30 and MP40 Multi-Processors [SEBU7750]
SERVICE EQUIPMENT AND SUPPLIES
SHIPPING GP
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
MP15, MP20, MP30 and MP40 Multi-Processors Shipping


NOTICE

For specific information on your host machine, refer to the Operation and Maintenance Manual of your host machine.




Illustration 1g02149792

When transporting the work tool on the host machine, position the work tool so the stick can be moved under the boom. Carry the boom as low as possible.

For additional information on transporting the work tool on the host machine, refer to the Operation and Maintenance Manual, "Slope Operation" of the host machine.



Illustration 2g01888480

When you must transport the work tool on another vehicle, position the work tool with the jaws in the OPEN position. Position the work tool with the jaws flat on the bed of the vehicle and with the lifting eye in an UPWARD position.



Illustration 3g01722093
MP15 and MP20 Transport lock pin


Illustration 4g01941693
MP30 Plate for the transport lock


Illustration 5g01444317
MP40 Plate for the transport lock

The MP15 and MP20 are equipped with a pin that locks the rotator. The MP30 and MP40 are equipped with a plate that locks the rotator. The transport locking device prevents the upper housing from moving when the work tool is transported.

Note: The transport locking device must be installed before the work tool will be removed from the host machine.

Note: The transport locking device must be removed when the work tool has been installed on the host machine and positioned in a vertical position.

Information System:

2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
2010/05/17 The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Compressor - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Condenser - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Cooler - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fuel Shutoff Solenoid - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base