MP15, MP20, MP30 and MP40 Multi-Processors Shipping Caterpillar


Shipping
`
MP15, MP20, MP30 and MP40 Multi-Processors [SEBU7750]
SERVICE EQUIPMENT AND SUPPLIES
SHIPPING GP
MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
MP15, MP20, MP30 and MP40 Multi-Processors Shipping
1.1. Shipping the Frame and Jaw set
2.1. Shipping the Jaw set

Shipping the Frame and Jaw set



Illustration 1g01888480

In order to ship the work tool, place the work tool on a suitable pallet or on the bed of a truck.

Position the work tool with the jaws in the OPEN position. Position the work tool with the jaws flat on the bed of the vehicle and with the lifting eye in an UPWARD position.

Use suitable tie-downs to secure the work tool for shipment.

Shipping the Jaw set



Illustration 2g02149978
Typical example jaw set in vertical position


Illustration 3g02157313
Typical example jaw set in horizontal position

If the jaw set has been removed from the frame, place the jaw set on a pallet. Position the jaw set VERTICAL or HORIZONTAL with the jaws in the CLOSED position.

Use suitable tie-downs to secure the jaws set to the pallet.

Information System:

MP15, MP20, MP30 and MP40 Multi-Processors Transport Position
2010/04/30 The Pin Assembly and Pin Retention Is Improved on Certain Bucket Arrangements for the 385C Excavator {6068, 7562}
349E Excavator Hydraulic System Gear Pump (Pilot) - Test
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
2010/05/17 The Relay Switch for the Heater has been Relocated to Improve the Reliability of the Switch on Certain Excavators {1417}
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Compressor - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Water Temperature Regulator - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Refrigerant Condenser - Remove and Install
303.5E2 CR, 304E2 CR, 305.5E2 CR and 305E2 CR Mini Hydraulic Excavators Engine Supplement Hood - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Cooler - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Fan - Remove and Install
303.5D, 304D, 305.5D and 305D Mini Hydraulic Excavators Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick Bearings and Seals - Remove and Install
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Electronic Unit Injector - Install
C6.6 Industrial Engine Wastegate Solenoid - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C6.6 Industrial Engine Engine Oil Filter Base - Remove and Install
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Industrial Engine Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base