MP15, MP20, MP30 and MP40 Multi-Processors Rotator Gear - Lubricate Caterpillar


Rotator Gear - Lubricate
`
MP15, MP20, MP30 and MP40 Multi-Processors [SEBU7750]
SERVICE EQUIPMENT AND SUPPLIES
LUBRICANTS & FLUIDS
MP15, MP20, MP30 and MP40 Multi-Processors Bushings - Lubricate
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Gear - Lubricate
1.1. MP15 and MP20
2.1. MP30
3.1. MP40

MP15 and MP20



Illustration 1g01891836
MP15 and MP20

  1. Clean the fittings before you lubricate the fittings.

  2. Lubricate the rotator group for the work tool.

  3. There are two grease fittings (1) for the rotator group.

  4. Rotate the work tool 180 degrees.

  5. Lubricate the fittings (1) again.

Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.

MP30



Illustration 2g01951295
MP30

  1. Clean the fittings before you lubricate the fittings.

  2. Lubricate the rotator group for the work tool.

  3. There are two grease fittings (2) for the rotator group.

  4. Rotate the work tool 180 degrees.

  5. Lubricate the fittings (2) again.

Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.

MP40

  1. Clean the fittings before you lubricate the fittings.


    Illustration 3g01891837
    MP40

  2. Lubricate the rotator group for the work tool.

  3. There are two grease fittings (3) for the rotator group.


    Illustration 4g01891838
    MP40

  4. Lubricate the gear group for the rotator.

  5. There are four grease fittings (4) for the gear group.

  6. Rotate the work tool 180 degrees.

  7. Lubricate the fittings (3) and the fittings (4) again.

Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.

Information System:

MP15, MP20, MP30 and MP40 Multi-Processors Bushings - Lubricate
C9.3 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
349E Excavator Hydraulic System Return Hydraulic System
C6.6 Industrial Engine Flywheel Housing - Remove and Install - Standard Housing
C6.6 Industrial Engine Crankshaft Rear Seal - Install
C6.6 Industrial Engine Crankshaft Rear Seal - Remove
C6.6 Industrial Engine Flywheel - Install
C6.6 Industrial Engine Flywheel - Remove
C6.6 Industrial Engine Water Temperature Regulator - Remove and Install
C6.6 Industrial Engine Water Pump - Install
C6.6 Industrial Engine Water Pump - Remove
C6.6 Industrial Engine Engine Oil Pump - Install
MP15, MP20, MP30 and MP40 Multi-Processors Cutting Edges - Inspect/Replace
Improved Jacket Water Circuit Breaker for Certain Electric Power Generators and Work Tools{1383, 1417, 1420}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Stick - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
2010/05/20 An Improved Hydraulic Tank is Available for Certain Excavators {5056}
2010/05/06 Improved Remanufactured Injectors Are Now Used on Some 3408E and 3412E Machine Engines {1251, 1254, 1290, 1713}
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Check
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Rotator Head Bolts - Inspect