Radiator Core - Clean
`
330F MHPU Mobile Hydraulic Power Unit
[M0066062]
330F MHPU Mobile Hydraulic Power Unit
Fuel System Secondary Filter - Replace
330F MHPU Mobile Hydraulic Power Unit
Engine and Machine Warm-Up
COOLING SYSTEM
RADIATOR GP
320E and 323E Excavators
Cooling System Coolant Extender (ELC) - Add
320E and 323E Excavators
Cooling System Coolant Level - Check
330F MHPU Mobile Hydraulic Power Unit
Radiator Core - Clean
320E and 323E Excavators
Cooling System Coolant (ELC) - Change
Show/hide table
 |
|
Personal injury can result from air pressure. Personal injury can result without following proper procedure. When using pressure air, wear a protective face shield and protective clothing. Maximum air pressure at the nozzle must be less than |
- Open the access door on the left side of the machine.
Show/hide table
Illustration 1 g02257254 - Unlatch the after cooler and A/C condenser core.
Show/hide table
Illustration 2 g02256553 - Swing the after cooler/AC condenser upward.
Show/hide table
Illustration 3 g02258615 - Remove dust and debris from all of the core fins.
Compressed air is preferred, but high-pressure water or steam can be used to remove dust and general debris from a core.
See Special Publication, SEBD0518, "Know Your Cooling System" for more detailed information about cleaning core fins.
- Close and latch the cooler/condenser.
- Close the access door on the left side of the machine.
Information System:
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Combined Function Hydraulic System - System 17
Procedure to Salvage Tang Slots on Transmission and Brake Pistons {0679, 3160, 4011, 4251}
390D Excavator
Lifting Capacities - 390D L
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems
Oil Filter (Hydraulic)
Procedure to Adjust Track Tension with Restricted Access to Fill Valve{7050}
2012/11/30
New Crankshaft for the C6.6 Machine Engines {1202}
2011/11/07
The Swing Bearing In the Bearing And Gear Group Is Improved on Certain 330D, 345C and 345D Excavators and 345C and 345D Mobile Hydraulic Power Units {7063}
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems
Final Drive - Assemble - Type-One
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems
Final Drive - Disassemble - Type-One
330F MHPU Mobile Hydraulic Power Unit
Fuel System Secondary Filter - Replace
320E Excavator
Fuel System Primary Filter (Water Separator) Element - Replace
Removal, Installation, and Conditioning of Idler Bearings and Track Roller Bearings {4159, 4159, 4180, 4180, 7551}
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Work Tool Parameter - Default Values - System 17
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Safety Messages
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Auxiliary) - Test and Adjust - Line, System 17
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Auxiliary) - Test and Adjust - Main (Medium Pressure), System 17
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Specifications
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Plate Locations and Film Locations
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Declaration of Conformity
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Daily Inspection
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Work Tool Installation and Removal
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Operation
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Transport Position
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Bushings - Lubricate