Bushings - Lubricate
`
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
[SEBU7751]
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Transport Position
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Crusher Tooth and Ripper Tooth - Replace
FRAME AND BODY
HOUSING GP
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Bushings - Lubricate
Note: Wipe all of the fittings before you lubricate the fittings.
Lubricate the fittings on the work tool. Refer to the following illustrations and tables for the locations of the lubrication points.
Show/hide table
 | |
| Illustration 1 | g02150061 |
VT-30, VT-40 and VT-50 | |
Show/hide table
| VT-30, VT-40, and VT-50 Multi-Processors | ||
| Lubrication Points | Number of Fittings | Callout |
| Cylinder Rod | 1 | LP1 |
| Cylinder Pin | 1 | LP3 |
| Frame Pin | 2 | LP4 |
| Cylinder Bearing | 2 | LP5 |
Show/hide table
 | |
| Illustration 2 | g02150062 |
VT-60 | |
Show/hide table
| VT-60 Multi-Processors | ||
| Lubrication Points | Number of Fittings | Callout |
| Cylinder Rod | 1 | LP1 |
| Cylinder Pin | 1 | LP4 |
| Frame Pin | 2 | LP5 |
| Cylinder Bearing | 2 | LP6 |
Refer to, "General Maintenance Information" for information on lubricants.
Information System:
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Transport Position
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Operation
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Work Tool Installation and Removal
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Daily Inspection
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Declaration of Conformity
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Plate Locations and Film Locations
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Specifications
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Auxiliary) - Test and Adjust - Main (Medium Pressure), System 17
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Relief Valve (Auxiliary) - Test and Adjust - Line, System 17
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Safety Messages
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Work Tool Parameter - Default Values - System 17
330F MHPU Mobile Hydraulic Power Unit
Radiator Core - Clean
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Crusher Tooth and Ripper Tooth - Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Crusher Tooth and Ripper Tooth - Tighten
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Cutting Edges - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Jaw - Repair
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Gear - Lubricate
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Wear Plates - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Wear Tip - Inspect/Replace