VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth

Crusher Tooth and Ripper Tooth - Replace

VT-30, VT-40, VT-50 and VT-60 Multi-Processors [SEBU7751]

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Bushings - Lubricate

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth - Tighten

WORK TOOLS

GROUND ENGAGING TOOLS (G.E.T.)

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth - Replace

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth - Tighten

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Cutting Edges - Inspect/Replace

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Wear Plates - Inspect/Replace

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Wear Tip - Inspect/Replace

1.1. Crusher Tooth

2.1. Ripper Tooth

Crusher Tooth

Open the jaws of the work tool.

Lock the jaws in an open position. The following procedure describes maintaining the jaws in the open position.
1. In order to hold the movable jaw in the open position, install clamp gp (1) onto cover (2) . The clamp gp (1) must be installed behind guide block (3) for the cover. Refer to Table 1 for the part numbers of the clamp gp.
  Show/hide table
  Table 1
  Clamp GP ⁽¹⁾
  
  Sales Model Part Number
  
  VT-30 200-2959
  
  VT-40 200-2960
  
  VT-50 200-2885
  
  VT-60 200-2961
  
  Show/hide table
  
  ^( 1 ) Part of the maintenance kit

Table 1
Clamp GP ⁽¹⁾
Sales Model	Part Number
VT-30	200-2959
VT-40	200-2960
VT-50	200-2885
VT-60	200-2961

Show/hide table




Illustration 2	g01890654

Remove the nut and remove the bolt (4) .

Remove the crusher tooth (5) .

Show/hide table




Illustration 3	g01890655

Clean the seat (6) for the crusher tooth.

Show/hide table




Illustration 4	g01968242
VT-30, VT-40, VT-50 and VT-60

Inspect the seat (6) for wear.

When the dimensions of the tooth seat are not within the service limit dimensions, the tooth seat must be reworked back to the original dimensions of the tooth seat. Refer to table 2 and table 3 for dimensions of the seat.

ReferenceRefer to , "Procedure for Buildup and Hard Surfacing of the Jaw Set" for additional information.

Show/hide table

Table 2
Type	Sales Model	Tooth Part Number	Service Limit Dimensions for Seat (6)
			A	B	C	D	E
			max	max	max	min	min
Crusher Tooth	VT-30	169-0383	74 mm (2.91 inch)	25.5 mm (1 inch)	74 mm (2.91 inch)	92 mm (3.62 inch)	38 mm (1.5 inch)
Crusher Tooth	VT-40, VT-50	280-9200	74 mm (2.91 inch)	30.5 mm (1.2 inch)	74 mm (2.91 inch)	112 mm (4.41 inch)	48 mm (1.89 inch)
Crusher Tooth	VT-60	169-4642	95 mm (3.74 inch)	36 mm (1.42 inch)	94 mm (3.7 inch)	140 mm (5.51 inch)	58 mm (2.28 inch)

Show/hide table

Table 3
Type	Sales Model	Tooth Part Number	Original Tooth Seat (6) Dimensions
			A	B	C	D	E
			-	-	-	-	max
Crusher Tooth	VT-30	169-0383	71 mm (2.80 inch)	25 mm (0.98 inch)	71 mm (2.80 inch)	93.5 mm (3.68 inch)	42 mm (1.65 inch)
Crusher Tooth	VT-40, VT-50	280-9200	71 mm (2.80 inch)	30 mm (1.18 inch)	71 mm (2.80 inch)	113.5 mm (4.47 inch)	52 mm (2.05 inch)
Crusher Tooth	VT-60	169-4642	92 mm (3.62 inch)	35 mm (1.38 inch)	92 mm (3.62 inch)	141.5 mm (5.57 inch)	62 mm (2.44 inch)

Install the new crusher tooth (5) .

Coat the threads of the new bolt (4) with 5P-3931 Anti-Seize Compound .
Note: Use a new bolt and a new nut when the crusher tooth will be replaced.

Install the new bolt (4) and install the new nut. Tighten the bolt and the nut.

Refer to , "General Maintenance Information" for additional information.

Ripper Tooth

Open the jaws of the work tool.

Lock the jaws in an open position. Refer to , "Crusher Tooth" for the proper procedure.

Show/hide table




Illustration 5	g01893654
VT-30, VT-40 and VT-50

Show/hide table




Illustration 6	g01943764
VT-60

Remove the bolt (7) .
Note: On models VT-30, VT-40, and VT-50, the ripper tooth is installed onto the jaw with one bolt. On the model VT-60, the ripper tooth is installed onto the jaw with two bolts.

Remove the ripper tooth (8) .

Show/hide table




Illustration 7	g01893673
VT-30, VT-40 and VT-50

Show/hide table




Illustration 8	g01943765
VT-60

Clean the seat (9) for the ripper tooth.

Show/hide table




Illustration 9	g02463096
VT-30, VT-40 and VT-50

Show/hide table




Illustration 10	g02463097
VT-60

Inspect the seat (9) for wear.

When the dimensions of the tooth seat are not within the service limit dimensions, the tooth seat must be reworked back to the original dimensions of the tooth seat. Refer to table 4 and table 5 for dimensions of the seat.

ReferenceRefer to , "Procedure for Buildup and Hard Surfacing of the Jaw Set" for additional information.

Show/hide table

Table 4
Type	Sales Model	Tooth Part Number	Service Limit Dimensions for Seat (9)
			A	B	C	D	E
			max	max	max	min	min
Ripper Tooth	VT-30, VT-40, VT-50	169-6069	85 mm (3.35 inch)	31 mm (1.22 inch)	83 mm (3.27 inch)	196 mm (7.72 inch)	48 mm (1.89 inch)
Ripper Tooth	VT-60	173-1692	95 mm (3.74 inch)	36 mm (1.42 inch)	94 mm (3.7 inch)	136 mm (5.35 inch)	58 mm (2.28 inch)

Show/hide table

Table 5
Type	Sales Model	Tooth Part Number	Original Tooth Seat (9) Dimensions
			A	B	C	D	E
			-	-	-	-	max
Ripper Tooth	VT-30, VT-40, VT-50	169-6069	82 mm (3.23 inch)	30 mm (1.18 inch)	82 mm (3.23 inch)	198 mm (7.80 inch)	52 mm (2.05 inch)
Ripper Tooth	VT-60	173-1692	92 mm (3.62 inch)	35 mm (1.38 inch)	92 mm (3.62 inch)	138 mm (5.43 inch)	62 mm (2.44 inch)

Install the new ripper tooth (8) .

Coat the threads of the new bolt (7) with 5P-3931 Anti-Seize Compound .
Note: Use a new bolt when the ripper tooth will be replaced.

Install the new bolt (7) . Tighten the bolt.
Note: On models VT-30, VT-40, and VT-50, the ripper tooth is installed onto the jaw with one bolt. On the model VT-60, the ripper tooth is installed onto the jaw with two bolts.

Refer to , "General Maintenance Information" for additional information.