Rotator Gear - Lubricate
`
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
[SEBU7751]
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Jaw - Repair
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
SERVICE EQUIPMENT AND SUPPLIES
LUBRICANTS & FLUIDS
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Bushings - Lubricate
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Gear - Lubricate
1.1. VT-30 and VT-40
2.1. VT-50
3.1. VT-60
VT-30 and VT-40
Show/hide table
 | |
| Illustration 1 | g01891836 |
VT-30 and VT-40 | |
- Clean the fittings before you lubricate the fittings.
- Lubricate the rotator group for the work tool.
- There are two grease fittings (1) for the rotator group.
- Rotate the work tool 180 degrees.
- Lubricate the fittings (1) again.
Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.
VT-50
Show/hide table
 | |
| Illustration 2 | g01951295 |
VT-50 | |
- Clean the fittings before you lubricate the fittings.
- Lubricate the rotator group for the work tool.
- There are two grease fittings (2) for the rotator group.
- Rotate the work tool 180 degrees.
- Lubricate the fittings (2) again.
Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.
VT-60
- Clean the fittings before you lubricate the fittings.
- Lubricate the rotator group for the work tool.
Show/hide table
 | |
| Illustration 3 | g01891837 |
VT-60 | |
- There are two grease fittings (3) for the rotator group.
- Lubricate the gear group for the rotator.
Show/hide table
 | |
| Illustration 4 | g01891838 |
VT-60 | |
- There are four grease fittings (4) for the gear group.
- Rotate the work tool 180 degrees.
- Lubricate the fittings (3) and the fittings (4) again.
Note: In addition to standard maintenance intervals, lubricate the work tool if the work tool has not been operated for some time.
Information System:
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Jaw - Repair
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Cutting Edges - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Crusher Tooth and Ripper Tooth - Tighten
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Crusher Tooth and Ripper Tooth - Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Bushings - Lubricate
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Transport Position
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Operation
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Work Tool Installation and Removal
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Daily Inspection
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Declaration of Conformity
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Plate Locations and Film Locations
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Specifications
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Wear Plates - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Wear Tip - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors
Maintenance Interval Schedule
325 VM and VH Variable Gauge Undercarriage
Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
326F Excavator
Hydraulic System Oil Filter (Pilot) - Replace
Repair of Transmission, Torque Converter, and Torque Divider Shafts {0679, 3000, 3063, 3100}
450E Backhoe Loader Axles, Differential and Brakes
Visual Inspection