EPC Parts Catalogs

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Maintenance Interval Schedule Caterpillar


  1. Home
  2. Operation and Maintenance Manual
  3. #82348
Maintenance Interval Schedule
`
VT-30, VT-40, VT-50 and VT-60 Multi-Processors [SEBU7751]
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Wear Tip - Inspect/Replace
WORK TOOL ARRANGEMENT
D6F SR, D6G and D6G SR Track-Type Tractors Operation
P16, P20, P25, P28, P40 and P60 Pulverizer Fire Prevention and Explosion Prevention
VT30, VT40, VT50 and VT60 Multi-Processors General Hazard Information
VT30, VT40, VT50 and VT60 Multi-Processors General Maintenance Information

When Required

Crusher Tooth and Ripper Tooth - Replace
Cutting Edges - Inspect/Replace
Jaw - Repair
Wear Plates - Inspect/Replace
Wear Tip - Inspect/Replace

Every 10 Service Hours or Daily

Bushings - Lubricate
Crusher Tooth and Ripper Tooth - Tighten
Cutting Edges - Inspect/Replace
Cutting Edge Screws - Tighten
Rotator Gear - Lubricate
Rotator Head Bolts - Inspect
Rotator Head Bolts - Inspect
Rotator Head Bolts - Inspect
Wear Plates - Inspect/Replace
Wear Tip - Inspect/Replace

Every 100 Service Hours or 2 Weeks

Jaw - Check
Rotator Head Bolts - Check
Rotator Head Bolts - Check
Rotator Head Bolts - Check

Commissioning

Rotator Gear - Lubricate

Information System:

VT-30, VT-40, VT-50 and VT-60 Multi-Processors Wear Tip - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Wear Plates - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Head Bolts - Inspect
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Head Bolts - Check
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Rotator Gear - Lubricate
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Jaw - Repair
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Cutting Edges - Inspect/Replace
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth - Tighten
VT-30, VT-40, VT-50 and VT-60 Multi-Processors Crusher Tooth and Ripper Tooth - Replace
325 VM and VH Variable Gauge Undercarriage Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
326F Excavator Hydraulic System Oil Filter (Pilot) - Replace
Repair of Transmission, Torque Converter, and Torque Divider Shafts {0679, 3000, 3063, 3100}
450E Backhoe Loader Axles, Differential and Brakes Visual Inspection
450E Backhoe Loader Axles, Differential and Brakes Differential Pinion Bearing - Adjust
450E Backhoe Loader Axles, Differential and Brakes Differential Backlash and Bearings - Adjust
374D Excavator Hydraulic System Travel Hydraulic System
450E Backhoe Loader Axles, Differential and Brakes Axle Housing and Bearing Preload - Adjust
374D Excavator Hydraulic System Swing Hydraulic System
450E Backhoe Loader Axles, Differential and Brakes Service Brake Control - Adjust
326F Excavator Hydraulic System Oil Filter (Case Drain) - Replace
329F and 330F Excavators Hydraulic System Oil - Change