303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Lifting Capacities Caterpillar

Lifting Capacities

303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators [SEBU8574]

303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Boom/Stick/Bucket Combinations

303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Safety Messages

MACHINE ARRANGEMENT

322B, 322B L, 325B and 325B L Excavators Towing the Machine

584 and 584HD Forwarders General Hazard Information

Show/hide table

Failure to comply to the rated load can cause possible personal injury or property damage. This includes the risk of unintended boom lowering. Review the rated load of a particular work tool before performing any operation. Make adjustments to the rated load as necessary for non-standard configurations.

Note: Lifting capacities are based upon a standard machine with the following conditions:

lubricants
full fuel tank
rubber track
canopy
75 kg (165 lb) operator

Lifting capacities will vary with different work tools and attachments. Consult your Cat dealer regarding the lifting capacities for specific work tools and attachments.

Note: Lifting capacities should be used as a guide. Work tools, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on lifting capacities. The operator is responsible for being aware of these effects.

For North American applications and European applications, the lifting capacities are defined by "ISO 10567 2007". The lifting capacities are defined as the lower value of 75% of the static tipping capacity or 87% of the hydraulic lift capacity.

The lifting capacities were calculated with a machine that was equipped with a standard bucket. The difference between the weight of a work tool attachment and the standard bucket must be subtracted.

This machine may be equipped with a standard stick or with a long stick. Lifting capacities may vary between a standard stick and a long stick. Measure the distance on the stick between the boom hinge pin and the work tool hinge pin. This distance will tell you if the machine is equipped with a standard stick or with a long stick.

303.5D CR

A Standard Stick is approximately 1260 mm (50 inch).
A Long Stick is approximately 1560 mm (61 inch).

304D CR

A Standard Stick is approximately 1315 mm (52 inch).
A Long Stick is approximately 1615 mm (64 inch).

305D CR

A Standard Stick is approximately 1351 mm (53 inch).
A Long Stick is approximately 1751 mm (69 inch).

305.5D CR

A Standard Stick is approximately 1418 mm (56 inch).
A Long Stick is approximately 1818 mm (72 inch).

Note: In European countries, regulations require a load sensing indicator and a boom lowering control device if more than 1000 kg (2200 lb) is lifted during object handling applications. Regulations also require a load sensing indicator and a boom lowering control device if a force that is greater than 40000 N·m (29500 lb ft) is created during object handling applications. If the machine is not equipped with these devices, even if the hydraulic lift capacity is capable, do not exceed a load of 1000 kg (2200 lb). Do not exceed a force of 40000 N·m (29500 lb ft) in European object handling applications.

Note: In European countries, regulations require the blade to be equipped with a lock if the blade is used to increase stability. If a mechanism that locks the position of the blade is not installed, use the values that are given in the tables for the machine when the blade is up. If a mechanism that locks the position of the blade is installed, use the values that are given in the tables for the machine when the blade is down.

303.5D CR

Show/hide table




Illustration 1	g00586902
(H) Height (F) Lifting capacity over the front of the machine (S) Lifting capacity over the side of the machine (R) Reach

Show/hide table

Table 1
303.5D CR with a Standard Stick, a 0.12 m³ (0.15 yd³) bucket, a 498 kg (1098 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft															660⁽²⁾ 1460⁽²⁾		3.24 10.63
3.5 m 11.5 ft							700⁽²⁾ 1540⁽²⁾		670⁽²⁾ 1480⁽²⁾	620 1370					600 1320	540 1190	3.74 12.27
3.0 m 10.0 ft							670⁽²⁾ 1480⁽²⁾		670 1480	610 1340					510 1120	460 1010	4.06 13.32
2.5 m 8.5 ft							760⁽²⁾ 1680⁽²⁾		660 1460	600 1320	520 1150	470 1040			450 990	410 900	4.32 14.17
2.0 m 6.5 ft					1100⁽²⁾ 2430⁽²⁾	1040 2290	850 1870	760 1680	650 1430	590 1300	520 1150	470 1040			420 930	380 840	4.50 14.76
1.5 m 5.0 ft							820 1810	740 1630	640 1410	570 1260	510 1120	460 1010	410 900	370 820	400 880	360 790	4.61 15.12
1.0 m 3.5 ft							790 1740	710 1570	620 1370	560 1240	500 1100	450 990	410 900	370 820	390 860	350 770	4.64 15.22
0.5 m 2.0 ft							780 1720	690 1520	610 1340	550 1210	490 1080	440 970	400 880	360 790	390 860	350 770	4.61 15.12
0					1040 2290	920 2030	770 1700	690 1520	600 1320	540 1190	480 1060	440 970			400 880	360 790	4.50 14.76
-0.5 m -2.0 ft			1580 3480	1370 3020	1040 2290	920 2030	760 1680	680 1500	600 1320	540 1190	480 1060	440 970			430 950	390 860	4.31 14.14
-1.0 m -3.5 ft	2170⁽²⁾ 4780⁽²⁾		1590 3500	1370 3020	1050 2310	930 2050	770 1700	690 1520	600 1320	540 1190					480 1060	440 970	4.02 13.19
-1.5 m 5.0 ft	1690⁽²⁾ 3730⁽²⁾		1450⁽²⁾ 3200⁽²⁾	1390 3060	1060 2340	940 2070	780 1720	700 1540	610 1340	550 1210					580 1280	520 1150	3.61 11.84
-2.0 m 6.5 ft			890⁽²⁾ 1960⁽²⁾		780⁽²⁾ 1720⁽²⁾										560⁽²⁾ 1240⁽²⁾		3.01 9.88

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 2
303.5D CR with a Standard Stick, a 0.12 m³ (0.15 yd³) bucket, a 498 kg (1098 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft															660⁽²⁾ 1460⁽²⁾		3.24 10.63
3.5 m 11.5 ft							700⁽²⁾ 1540⁽²⁾		670⁽²⁾ 1480⁽²⁾	670 1480					670⁽²⁾ 1480⁽²⁾	590 1300	3.74 12.27
3.0 m 10.0 ft							670⁽²⁾ 1480⁽²⁾		680⁽²⁾ 1500⁽²⁾	660 1460					660⁽²⁾ 1460⁽²⁾	500 1100	4.06 13.32
2.5 m 8.5 ft							760⁽²⁾ 1680⁽²⁾		720⁽²⁾ 1590⁽²⁾	650 1430	700⁽²⁾ 1540⁽²⁾	510 1120			660⁽²⁾ 1460⁽²⁾	450 990	4.32 14.17
2.0 m 6.5 ft					1100⁽²⁾ 2430⁽²⁾		910⁽²⁾ 2010⁽²⁾	830 1830	800⁽²⁾ 1760⁽²⁾	640 1410	730⁽²⁾ 1610⁽²⁾	510 1120			650⁽²⁾ 1430⁽²⁾	410 900	4.50 14.76
1.5 m 5.0 ft							1090⁽²⁾ 2400⁽²⁾	800 1760	900⁽²⁾ 1980⁽²⁾	620 1370	780⁽²⁾ 1720⁽²⁾	500 1100	710⁽²⁾ 1570⁽²⁾	410 900	660⁽²⁾ 1460⁽²⁾	390 860	4.61 14.12
1.0 m 3.5 ft							1260⁽²⁾ 2780⁽²⁾	770 1700	990⁽²⁾ 2180⁽²⁾	610 1340	840⁽²⁾ 1850⁽²⁾	490 1080	730⁽²⁾ 1610⁽²⁾	400 880	690⁽²⁾ 1520⁽²⁾	380 840	4.64 15.22
0.5 m 2.0 ft							1350⁽²⁾ 2980⁽²⁾	760 1680	1060⁽²⁾ 2340⁽²⁾	600 1320	870⁽²⁾ 1920⁽²⁾	480 1060	740⁽²⁾ 1630⁽²⁾	400 880	710⁽²⁾ 1570⁽²⁾	380 840	4.61 15.12
0					1790⁽²⁾ 3950⁽²⁾	1000 2200	1370⁽²⁾ 3020⁽²⁾	750 1650	1080⁽²⁾ 2380⁽²⁾	590 1300	880⁽²⁾ 1940⁽²⁾	480 1060			720⁽²⁾ 1590⁽²⁾	400 880	4.50 14.76
-0.5 m -2.0 ft			1760⁽²⁾ 3880⁽²⁾	1500 3300	1660⁽²⁾ 3660⁽²⁾	1010 2230	1320⁽²⁾ 2910⁽²⁾	750 1650	1050⁽²⁾ 2310⁽²⁾	580 1280	840⁽²⁾ 1850⁽²⁾	480 1060			720⁽²⁾ 1590⁽²⁾	420 930	4.31 15.14
-1.0 m -3.5 ft	2170⁽²⁾ 4780⁽²⁾		1800⁽²⁾ 3970⁽²⁾	1510 3330	1480⁽²⁾ 3260⁽²⁾	1010 2230	1190⁽²⁾ 2620⁽²⁾	750 1650	950⁽²⁾ 2100⁽²⁾	590 1300					710⁽²⁾ 1570⁽²⁾	480 1060	4.02 13.19
-1.5 m 5.0 ft	1690⁽²⁾ 3730⁽²⁾		1450⁽²⁾ 3200⁽²⁾		1210⁽²⁾ 2670⁽²⁾	1020 2250	980⁽²⁾ 2160⁽²⁾	760 1680	750⁽²⁾ 1650⁽²⁾	600 1320					670⁽²⁾ 1480⁽²⁾	570 1260	3.61 11.84
-2.0 m 6.5 ft			890⁽²⁾ 1960⁽²⁾		780⁽²⁾ 1720⁽²⁾										560⁽²⁾ 1240⁽²⁾		3.01 9.88

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 3
303.5D CR with a Long Stick, a 0.12 m³ (0.15 yd³) bucket, a 498 kg (1098 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft															600⁽²⁾ 1320⁽²⁾		3.13 10.27
4.0 m 13.0 ft															600⁽²⁾ 1320⁽²⁾	580 1280	3.60 11.81
3.5 m 11.5 ft									570⁽²⁾ 1260⁽²⁾						520 1150	470 1040	4.03 13.22
3.0 m 10.0 ft									560⁽²⁾ 1240⁽²⁾		520 1150	470 1040			450 990	400 880	4.32 14.17
2.5 m 8.5 ft									610⁽²⁾ 1340⁽²⁾	600 1320	520 1150	470 1040	410 900	370 820	400 880	360 790	4.58 15.03
2.0 m 6.5 ft							760⁽²⁾ 1680⁽²⁾		650 1430	580 1280	510 1120	460 1010	410 900	370 820	370 820	330 730	4.76 15.62
1.5 m 5.0 ft					1120 2470	990 2180	820 1810	730 1610	630 1390	570 1260	500 1100	450 990	400 880	360 790	350 770	310 680	4.86 15.94
1.0 m 3.5 ft							790 1740	700 1540	610 1340	550 1210	490 1080	440 970	390 860	360 790	340 750	300 660	4.89 16.04
0.5 m 2.0 ft					1020 2250	900 1980	760 1680	680 1500	590 1300	530 1170	470 1040	430 950	390 860	350 770	340 750	300 660	4.85 15.91
0					1010 2230	890 1960	750 1650	660 1460	580 1280	520 1150	470 1040	420 930	380 840	340 750	350 770	310 680	4.75 15.58
-0.5 m -2.0 ft	1200⁽²⁾ 2650⁽²⁾		1530 3370	1320 2910	1010 2230	890 1960	740 1630	660 1460	580 1280	510 1120	460 1010	410 900	380 840	340 750	370 820	330 730	4.58 15.03
-1.0 m -3.5 ft	1890⁽²⁾ 4170⁽²⁾		1540 3400	1330 2930	1010 2230	890 1960	740 1630	660 1460	570 1260	510 1120	460 1010	420 930			410 900	370 820	4.31 14.14
-1.5 m -5.0 ft	2510⁽²⁾ 5530⁽²⁾	2410 5313	1550 3420	1340 2950	1020 2250	900 1980	750 1650	660 1460	580 1280	520 1150					480 1060	430 950	3.95 12.96
-2.0 m -6.5 ft	1700⁽²⁾ 3750⁽²⁾		1320⁽²⁾ 2910⁽²⁾		1040 2290	920 2030	760 1680	680 1500							610 1350	550 1210	3.43 11.25
-2.5 m -8.5 ft					480⁽²⁾ 1060⁽²⁾										450⁽²⁾ 990⁽²⁾		2.59 8.50

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 4
303.5D CR with a Long Stick, a 0.12 m³ (0.15 yd³) bucket, a 498 kg (1098 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft															600⁽²⁾ 1320⁽²⁾		3.13 10.27
4.0 m 13.0 ft															600⁽²⁾ 1320⁽²⁾		3.60 11.81
3.5 m 11.5 ft									570⁽²⁾ 1260⁽²⁾						600⁽²⁾ 1320⁽²⁾	510 1120	4.03 13.22
3.0 m 10.0 ft									560⁽²⁾ 1240⁽²⁾		580⁽²⁾ 1280⁽²⁾	510 1120			610⁽²⁾ 1340⁽²⁾	440 970	4.32 14.17
2.5 m 8.5 ft									610⁽²⁾ 1340⁽²⁾		600⁽²⁾ 1320⁽²⁾	510 1120	600⁽²⁾ 1320⁽²⁾	410 900	610⁽²⁾ 1340⁽²⁾	390 860	4.58 15.03
2.0 m 6.5 ft							760⁽²⁾ 1680⁽²⁾		690 1520	630 1390	650⁽²⁾ 1430⁽²⁾	500 1100	620⁽²⁾ 1370⁽²⁾	400 880	610⁽²⁾ 1340⁽²⁾	360 790	4.76 15.62
1.5 m 5.0 ft					1220⁽²⁾ 2690⁽²⁾	1080 2380	940⁽²⁾ 2070⁽²⁾	800 1760	800⁽²⁾ 1760⁽²⁾	610 1340	710⁽²⁾ 1570⁽²⁾	490 1080	650⁽²⁾ 1430⁽²⁾	400 880	620⁽²⁾ 1370⁽²⁾	340 750	4.86 15.94
1.0 m 3.5 ft							1130⁽²⁾ 2490⁽²⁾	770 1700	910⁽²⁾ 2010⁽²⁾	600 1320	770⁽²⁾ 1700⁽²⁾	480 1060	680⁽²⁾ 1500⁽²⁾	390 860	630⁽²⁾ 1390⁽²⁾	330 730	4.89 16.04
0.5 m 2.0 ft					1790⁽²⁾ 3950⁽²⁾	990 2180	1280⁽²⁾ 2820⁽²⁾	740 1630	990⁽²⁾ 2180⁽²⁾	580 1280	820⁽²⁾ 1810⁽²⁾	470 1040	710⁽²⁾ 1570⁽²⁾	380 840	640⁽²⁾ 1410⁽²⁾	340 750	4.85 15.91
0					1820⁽²⁾ 4010⁽²⁾	980 2160	1340⁽²⁾ 2950⁽²⁾	730 1610	1040⁽²⁾ 2290⁽²⁾	570 1260	850⁽²⁾ 1870⁽²⁾	460 1010	720⁽²⁾ 1590⁽²⁾	380 840	650⁽²⁾ 1430⁽²⁾	350 770	4.75 15.58
-0.5 m -2.0 ft	1200⁽²⁾ 2650⁽²⁾		1670⁽²⁾ 3680⁽²⁾	1450 3200	1750⁽²⁾ 3860⁽²⁾	970 2140	1330⁽²⁾ 2930⁽²⁾	720 1590	1050⁽²⁾ 2310⁽²⁾	560 1240	850⁽²⁾ 1870⁽²⁾	450 990	690⁽²⁾ 1520⁽²⁾	380 840	660⁽²⁾ 1460⁽²⁾	370 820	4.58 15.03
-1.0 m -3.5 ft	1890⁽²⁾ 4170⁽²⁾		2120⁽²⁾ 4670⁽²⁾	1460 3220	1610⁽²⁾ 3550⁽²⁾	980 2160	1250⁽²⁾ 2760⁽²⁾	720 1590	990⁽²⁾ 2180⁽²⁾	560 1240	790⁽²⁾ 1740⁽²⁾	450 990			670⁽²⁾ 1480⁽²⁾	400 880	4.31 14.14
-1.5 m -5.0 ft	2510⁽²⁾ 5530⁽²⁾		1790⁽²⁾ 3950⁽²⁾	1480 3260	1390⁽²⁾ 3060⁽²⁾	990 2180	1100⁽²⁾ 2430⁽²⁾	730 1610	870⁽²⁾ 1920⁽²⁾	570 1260					660 1460	470 1040	3.95 12.96
-2.0 m -6.5 ft	1700⁽²⁾ 3750⁽²⁾		1320⁽²⁾ 2910⁽²⁾		1060⁽²⁾ 2340⁽²⁾	1000 2200	830⁽²⁾ 1830⁽²⁾	740 1630							620⁽²⁾ 1370⁽²⁾	600 1320	3.43 11.25
-2.5 m -8.5 ft					480⁽²⁾ 1060⁽²⁾										450⁽²⁾ 990⁽²⁾		2.59 8.50

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

304D CR

Show/hide table




Illustration 2	g00586902
(H) Height (F) Lifting capacity over the front of the machine (S) Lifting capacity over the side of the machine (R) Reach

Show/hide table

Table 5
304D CR with a Standard Stick, a 0.12 m³ (0.15 yd³) bucket, a 566 kg (1248 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft															630⁽²⁾ 1390⁽²⁾		3.52 11.55
3.5 m 11.5 ft									670⁽²⁾ 1480⁽²⁾						610⁽²⁾ 1340⁽²⁾		3.96 12.99
3.0 m 10.0 ft									670⁽²⁾ 1480⁽²⁾		610 1340	620 1370			540 1190	550 1210	4.26 13.98
2.5 m 8.5 ft							760⁽²⁾ 1680⁽²⁾		740⁽²⁾ 1630⁽²⁾		600 1320	610 1340			490 1080	500 1100	4.49 14.73
2.0 m 6.5 ft					1160⁽²⁾ 2560⁽²⁾		960⁽²⁾ 2120⁽²⁾		740 1630	760 1680	590 1300	610 1340	480 1060	490 1080	450 990	460 1010	4.67 15.32
1.5 m 5.0 ft							930 2050	940 2070	730 1610	740 1630	580 1280	590 1300	480 1060	490 1080	430 950	440 970	4.77 15.65
1.0 m 3.5 ft							900 1980	910 2010	710 1570	720 1590	570 1260	580 1280	470 1040	480 1060	420 930	430 950	4.80 15.75
0.5 m 2.0 ft							880 1940	890 1960	690 1520	710 1570	560 1240	570 1260	470 1040	480 1060	420 930	440 970	4.76 15.62
0					1170 2580	1180 2600	870 1920	880 1940	680 1500	700 1540	560 1240	570 1260	460 1010	470 1040	440 970	450 990	4.65 15.26
-0.5 m -2.0 ft			1780 3920	1770 3900	1170 2580	1180 2600	870 1920	880 1940	680 1500	690 1520	550 1210	560 1240			470 1040	480 1060	4.46 14.63
-1.0 m -3.5 ft	2440⁽²⁾ 5380⁽²⁾		1780 3920		1180 2600	1190 2620	870 1920	880 1940	680 1500	690 1520	550 1210	570 1260			520 1150	530 1170	4.19 13.75
-1.5 m -5.0 ft	2900⁽²⁾ 6390⁽²⁾		1800 3970	1790 3950	1190 2620	1200 2650	880 1940	890 1960	690 1520	700 1540					610 1340	620 1370	3.80 12.47
-2.0 m -6.5 ft	2090⁽²⁾ 4610⁽²⁾		1600⁽²⁾ 3530⁽²⁾		1210 2670	1220 2690	890 1960	910 2010							800 1760	810 1790	3.23 10.60

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 6
304D CR with a Standard Stick, a 0.12 m³ (0.15 yd³) bucket, a 566 kg (1248 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft															630⁽²⁾ 1390⁽²⁾		3.52 11.55
3.5 m 11.5 ft									670⁽²⁾ 1480⁽²⁾						610⁽²⁾ 1340⁽²⁾		3.96 12.99
3.0 m 10.0 ft									670⁽²⁾ 1480⁽²⁾		700⁽²⁾ 1540⁽²⁾	680 1500			610⁽²⁾ 1340⁽²⁾	600 1320	4.26 13.98
2.5 m 8.5 ft							760⁽²⁾ 1680⁽²⁾		740⁽²⁾ 1630⁽²⁾		730⁽²⁾ 1610⁽²⁾	670 1480			600⁽²⁾ 1320⁽²⁾	550 1210	4.49 14.73
2.0 m 6.5 ft					1160⁽²⁾ 2560⁽²⁾		960⁽²⁾ 2120⁽²⁾		850⁽²⁾ 1870⁽²⁾	830 1830	780⁽²⁾ 1720⁽²⁾	660 1460	750⁽²⁾ 1650⁽²⁾	540 1190	600⁽²⁾ 1320⁽²⁾	510 1120	4.67 15.32
1.5 m 5.0 ft							1190⁽²⁾ 2620⁽²⁾	1030 2270	980⁽²⁾ 2160⁽²⁾	810 1790	860⁽²⁾ 1890⁽²⁾	650 1430	790⁽²⁾ 1740⁽²⁾	540 1190	610⁽²⁾ 1340⁽²⁾	490 1080	4.77 15.65
1.0 m 3.5 ft							1420⁽²⁾ 3130⁽²⁾	1000 2200	1110⁽²⁾ 2450⁽²⁾	790 1740	940⁽²⁾ 2070⁽²⁾	640 1410	830⁽²⁾ 1830⁽²⁾	530 1170	640⁽²⁾ 1410⁽²⁾	480 1060	4.80 15.75
0.5 m 2.0 ft							1560⁽²⁾ 3440⁽²⁾	980 2160	1210⁽²⁾ 2670⁽²⁾	770 1700	1000⁽²⁾ 2200⁽²⁾	630 1390	870⁽²⁾ 1920⁽²⁾	520 1150	680⁽²⁾ 1500⁽²⁾	480 1060	4.76 15.62
0					2130⁽²⁾ 4700⁽²⁾	1310 2890	1610⁽²⁾ 3550⁽²⁾	970 2140	1260⁽²⁾ 2780⁽²⁾	770 1700	1040⁽²⁾ 2290⁽²⁾	620 1370	870⁽²⁾ 1920⁽²⁾	520 1150	740⁽²⁾ 1630⁽²⁾	490 1080	4.65 15.26
-0.5 m -2.0 ft			1920⁽²⁾ 4230⁽²⁾		2040⁽²⁾ 4500⁽²⁾	1310 2890	1590⁽²⁾ 3500⁽²⁾	970 2140	1260⁽²⁾ 2780	760 1680	1030⁽²⁾ 2270⁽²⁾	620 1370			830⁽²⁾ 1830⁽²⁾	530 1170	4.46 14.63
-1.0 m -3.5 ft	2440⁽²⁾ 5380⁽²⁾		2420⁽²⁾ 5340⁽²⁾	1990 4390	1890⁽²⁾ 4170⁽²⁾	1320 2910	1500⁽²⁾ 3310⁽²⁾	970 2140	1200⁽²⁾ 2650⁽²⁾	760 1680	960⁽²⁾ 2120⁽²⁾	620 1370			870⁽²⁾ 1920⁽²⁾	580 1280	4.19 13.75
-1.5 m -5.0 ft	2900⁽²⁾ 6390⁽²⁾		2110⁽²⁾ 4650⁽²⁾	2000 4410	1660⁽²⁾ 3660⁽²⁾	1330 2930	1330⁽²⁾ 2930⁽²⁾	980 2160	1050⁽²⁾ 2310⁽²⁾	770 1700					880⁽²⁾ 1940⁽²⁾	680 1500	3.80 12.47
-2.0 m -6.5 ft	2090⁽²⁾ 4610⁽²⁾		1600⁽²⁾ 3530⁽²⁾		1290⁽²⁾ 2840⁽²⁾		1010⁽²⁾ 2230⁽²⁾	1000 2200							850⁽²⁾ 1870⁽²⁾		3.23 10.60

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 7
304D CR with a Long Stick, a 0.12 m³ (0.15 yd³) bucket, a 566 kg (1248 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							790⁽²⁾ 1740⁽²⁾
1.5 m 5.0 ft					1270 2800	1280 2820	940 2070	950 2100
1.0 m 3.5 ft							900 1980	910 2010
0.5 m 2.0 ft					1170 2580	1180 2600	880 1940	890 1960
0					1160 2560		860 1890	870 1920
-0.5 m -2.0 ft	1360⁽²⁾ 3000⁽²⁾		1740 3840	1730 3810	1150 2540	1160 2560	850 1870	860 1890
-1.0 m -3.5 ft	2100⁽²⁾ 4630⁽²⁾		1740 3840		1160 2560		850 1870	860 1890
-1.5 m -5.0 ft	2840⁽²⁾ 6260⁽²⁾		1760 3880	1750 3860	1160 2560	1170 2580	860 1890	870 1920
-2.0 m -6.5 ft	2990⁽²⁾ 6590⁽²⁾		1780 3920	1770 3900	1180 2600	1190 2620	870 1920	880 1940
-2.5 m -8.5 ft			1350⁽²⁾ 2980⁽²⁾		1050⁽²⁾ 2310⁽²⁾
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft									600⁽²⁾ 1320⁽²⁾		3.85 12.63
3.5 m 11.5 ft			600⁽²⁾ 1320⁽²⁾						550 1210	560 1240	4.24 13.91
3.0 m 10.0 ft	550⁽²⁾ 1210⁽²⁾		590⁽²⁾ 1300⁽²⁾						490 1080	500 1100	4.52 14.83
2.5 m 8.5 ft	620⁽²⁾ 1370⁽²⁾		600 1320	620 1370	490 1080	500 1100			440 970	450 990	4.76 15.62
2.0 m 6.5 ft	730⁽²⁾ 1610⁽²⁾		590 1300	610 1340	480 1060	490 1080			410 900	420 930	4.92 16.14
1.5 m 5.0 ft	730 1610	740 1630	580 1280	590 1300	470 1040	480 1060	390 860	400 880	390 860	400 880	5.01 16.44
1.0 m 3.5 ft	710 1570	720 1590	570 1260	580 1280	470 1040	480 1060	390 860	400 880	380 840	390 860	5.04 16.54
0.5 m 2.0 ft	690 1520	700 1540	550 1210	570 1260	460 1010	470 1040	380 840	390 860	380 840	390 860	5.00 16.40
0	670 1480	690 1520	550 1210	560 1240	450 990	460 1010			390 860	400 880	4.90 16.08
-0.5 m -2.0 ft	670 1480	680 1500	540 1190	550 1210	450 990	460 1010			410 900	430 950	4.73 15.52
-1.0 m -3.5 ft	660 1460	680 1500	540 1190	550 1210					450 990	460 1010	4.47 14.67
-1.5 m -5.0 ft	670 1480	680 1500	540 1190	560 1240					520 1150	530 1170	4.12 13.52
-2.0 m -6.5 ft	680 1500	690 1520							640 1410	660 1460	3.63 11.91
-2.5 m -8.5 ft									830⁽²⁾ 1830⁽²⁾		2.88 9.45

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 8
304D CR with a Long Stick, a 0.12 m³ (0.15 yd³) bucket, a 566 kg (1248 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							790⁽²⁾ 1740⁽²⁾
1.5 m 5.0 ft					1350⁽²⁾ 2980⁽²⁾		1030⁽²⁾ 2270⁽²⁾
1.0 m 3.5 ft							1270⁽²⁾ 2800⁽²⁾	1010 2230
0.5 m 2.0 ft					2080⁽²⁾ 4590⁽²⁾	1310 2890	1460⁽²⁾ 3220⁽²⁾	980 2160
0					2150⁽²⁾ 4740⁽²⁾	1290 2840	1570⁽²⁾ 3460⁽²⁾	960 2120
-0.5 m -2.0 ft	1360⁽²⁾ 3000⁽²⁾		1840⁽²⁾ 4060⁽²⁾		2110⁽²⁾ 4650⁽²⁾	1290 2840	1590⁽²⁾ 3500⁽²⁾	950 2100
-1.0 m -3.5 ft	2100⁽²⁾ 4630⁽²⁾		2620⁽²⁾ 5780⁽²⁾	1940 4280	2010⁽²⁾ 4430⁽²⁾	1290 2840	1540⁽²⁾ 3400⁽²⁾	950 2100
-1.5 m -5.0 ft	2840⁽²⁾ 6260⁽²⁾		2440⁽²⁾ 5380⁽²⁾	1960 4320	1830⁽²⁾ 4030⁽²⁾	1300 2870	1430⁽²⁾ 3150⁽²⁾	960 2120
-2.0 m -6.5 ft	2990⁽²⁾ 6590⁽²⁾		2010⁽²⁾ 4430⁽²⁾	1980 4370	1540⁽²⁾ 3400⁽²⁾	1320 2910	1210⁽²⁾ 2670⁽²⁾	970 2140
-2.5 m -8.5 ft			1350⁽²⁾ 2980⁽²⁾		1050⁽²⁾ 2310⁽²⁾
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft									600⁽²⁾ 1320⁽²⁾		3.85 12.63
3.5 m 11.5 ft			600⁽²⁾ 1320⁽²⁾						620⁽²⁾ 1370⁽²⁾	610 1340	4.24 13.91
3.0 m 10.0 ft	550⁽²⁾ 1210⁽²⁾		590⁽²⁾ 1300⁽²⁾						620⁽²⁾ 1370⁽²⁾	540 1190	4.52 14.83
2.5 m 8.5 ft	620⁽²⁾ 1370⁽²⁾		630⁽²⁾ 1390⁽²⁾		640⁽²⁾ 1410⁽²⁾	550 1210			610⁽²⁾ 1340⁽²⁾	490 1080	4.76 15.62
2.0 m 6.5 ft	730⁽²⁾ 1610⁽²⁾		690⁽²⁾ 1520⁽²⁾	660 1460	670⁽²⁾ 1480⁽²⁾	540 1190			610⁽²⁾ 1340⁽²⁾	460 1010	4.92 16.14
1.5 m 5.0 ft	870⁽²⁾ 1920⁽²⁾	810 1790	780⁽²⁾ 1720⁽²⁾	650 1430	720⁽²⁾ 1590⁽²⁾	530 1170	660⁽²⁾ 1460⁽²⁾	440 970⁽²⁾	630⁽²⁾ 1390⁽²⁾	440 970	5.01 16.44
1.0 m 3.5 ft	1010⁽²⁾ 2230⁽²⁾	790 1740	870⁽²⁾ 1920⁽²⁾	640 1410	780⁽²⁾ 1720⁽²⁾	520 1150	720⁽²⁾ 1590⁽²⁾	440 970	660⁽²⁾ 1460⁽²⁾	430 950	5.04 16.54
0.5 m 2.0 ft	1140⁽²⁾ 2510⁽²⁾	770 1700	950⁽²⁾ 2100⁽²⁾	620 1370	820⁽²⁾ 1810⁽²⁾	520 1150	710⁽²⁾ 1570⁽²⁾	430 950	700⁽²⁾ 1540⁽²⁾	430 950	5.00 16.40
0	1220⁽²⁾ 2690⁽²⁾	760 1680	1000⁽²⁾ 2200⁽²⁾	610 1340	860⁽²⁾ 1890⁽²⁾	510 1120			760⁽²⁾ 1680⁽²⁾	450 990	4.90 16.08
-0.5 m -2.0 ft	1250⁽²⁾ 2760⁽²⁾	750 1650	1020⁽²⁾ 2250⁽²⁾	610 1340	860⁽²⁾ 1890⁽²⁾	510 1120			790⁽²⁾ 1740⁽²⁾	470 1040	4.73 15.52
-1.0 m -3.5 ft	1230⁽²⁾ 2710⁽²⁾	750 1650	1000⁽²⁾ 2200	610 1340					810⁽²⁾ 1790⁽²⁾	510 1120	4.47 14.67
-1.5 m -5.0 ft	1140⁽²⁾ 2510⁽²⁾	750 1650	900⁽²⁾ 1980	610 1340					840⁽²⁾ 1850⁽²⁾	590 1300	4.12 13.52
-2.0 m -6.5 ft	930⁽²⁾ 2050⁽²⁾	760 1680							860⁽²⁾ 1890⁽²⁾	720 1590	3.63 11.91
-2.5 m -8.5 ft									830⁽²⁾ 1830⁽²⁾		2.88 9.45

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

305D CR

Show/hide table




Illustration 3	g00586902
(H) Height (F) Lifting capacity over the front of the machine (S) Lifting capacity over the side of the machine (R) Reach

Show/hide table

Table 9
305D CR with a Standard Stick, a 0.17 m³ (0.23 yd³) bucket, a 642 kg (1415 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft									1040⁽²⁾ 2290⁽²⁾	930 2050					840⁽²⁾ 1850⁽²⁾		3.86 12.67
3.5 m 11.5 ft									690⁽²⁾ 1520⁽²⁾		800⁽²⁾ 1760⁽²⁾	790 1740			860⁽²⁾ 1890⁽²⁾	710 1570	4.24 13.91
3.0 m 10.0 ft									760⁽²⁾ 1680⁽²⁾		820⁽²⁾ 1810⁽²⁾	790 1740			790 1740	610 1340	4.59 15.06
2.5 m 8.5 ft							930⁽²⁾ 2050⁽²⁾		910⁽²⁾ 2010⁽²⁾		900⁽²⁾ 1980⁽²⁾	780 1720	810 1790	630 1390	720 1590	560 1240	4.81 15.78
2.0 m 6.5 ft							1300⁽²⁾ 2870⁽²⁾	1220 2690	1110⁽²⁾ 2450⁽²⁾	950 2100	980 2160	760 1680	800 1760	620 1370	680 1500	520 1150	4.96 16.27
1.5 m 5.0 ft							1540 3400	1160 2560	1200 2650	920 2030	960 2120	740 1630	790 1740	610 1340	650 1430	500 1100	5.03 16.50
1.0 m 3.5 ft							1490 3280	1120 2470	1170 2580	890 1960	940 2070	720 1590	780 1720	600 1320	650 1430	500 1100	5.04 16.54
0.5 m 2.0 ft							1460 3220	1090 2400	1140 2510	870 1920	930 2050	710 1570	770 1700	590 1390	650 1430	500 1100	4.98 16.34
0							1450 3200	1090 2400	1130 2490	860 1890	920 2030	700 1540	760 1680	580 1280	680 1500	520 1150	4.85 15.91
-0.5 m -2.0 ft			2060⁽²⁾ 4540⁽²⁾		2010 4430	1470 3240	1450 3200	1090 2400	1130 2490	850 1870	910 2010	690 1520	760 1680	580 1280	730 1610	550 1210	4.64 15.22
-1.0 m -3.5 ft	2870⁽²⁾ 6330⁽²⁾		3190 7032	2220 4890	2020 4450	1480 3260	1460 3220	1090 2400	1130 2490	850 1870	910 2010	700 1540			810 1790	620 1370	4.34 14.24
-1.5 m -5.0 ft	3920⁽²⁾ 8640⁽²⁾		3210 7080	2230 4920	2040 4500	1490 3280	1470 3240	1100 2430	1140 2510	860 1890					960 2120	730 1610	3.92 12.86
-2.0 m -6.5 ft	3720⁽²⁾ 8200⁽²⁾		2590⁽²⁾ 5710⁽²⁾	2270 5000	2030⁽²⁾ 4480⁽²⁾	1520 3350	1500 3310	1120 2470							1200⁽²⁾ 2650⁽²⁾		2.16 7.08

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 10
305D CR with a Standard Stick, a 0.17 m³ (0.23 yd³) bucket, a 642 kg (1415 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		Maximum Reach
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.0 m 13.0 ft									1040⁽²⁾ 2290⁽²⁾	1030 2270					840⁽²⁾ 1850⁽²⁾		3.86 12.67
3.5 m 11.5 ft									690⁽²⁾ 1520⁽²⁾		800⁽²⁾ 1760⁽²⁾				860⁽²⁾ 1890⁽²⁾	790 1740	4.24 13.91
3.0 m 10.0 ft									760⁽²⁾ 1680⁽²⁾		820⁽²⁾ 1810⁽²⁾				820⁽²⁾ 1810⁽²⁾	680 1500	4.59 15.06
2.5 m 8.5 ft							930⁽²⁾ 2050⁽²⁾		910⁽²⁾ 2010⁽²⁾		900⁽²⁾ 1980⁽²⁾	860 1890	910⁽²⁾ 2010⁽²⁾	700 1540	810⁽²⁾ 1790⁽²⁾	620 1370	4.81 15.78
2.0 m 6.5 ft							1300⁽²⁾ 2870⁽²⁾		1110⁽²⁾ 2450⁽²⁾	1050 2310	1020⁽²⁾ 2250⁽²⁾	850 1870	970⁽²⁾ 2140⁽²⁾	690 1520	810⁽²⁾ 1790⁽²⁾	580 1280	4.96 16.27
1.5 m 5.0 ft							1750⁽²⁾ 3860⁽²⁾	1300 2870	1350⁽²⁾ 2980⁽²⁾	1020 2250	1160⁽²⁾ 2560⁽²⁾	830 1830	1050⁽²⁾ 2310⁽²⁾	680 1500	830⁽²⁾ 1830⁽²⁾	560 1240	5.03 16.50
1.0 m 3.5 ft							2110⁽²⁾ 4650⁽²⁾	1250 2760	1570⁽²⁾ 3460⁽²⁾	990 2180	1300⁽²⁾ 2870⁽²⁾	810 1790	1140⁽²⁾ 2510⁽²⁾	670 1480	870⁽²⁾ 1920⁽²⁾	560 1240	5.04 16.54
0.5 m 2.0 ft							2290⁽²⁾ 5050⁽²⁾	1230 2710	1730⁽²⁾ 3810⁽²⁾	970 2140	1410⁽²⁾ 3110⁽²⁾	790 1740	1210⁽²⁾ 2670⁽²⁾	660 1460	930⁽²⁾ 2050⁽²⁾	560 1240	4.98 16.34
0							2340⁽²⁾ 5160⁽²⁾	1220 2690	1820⁽²⁾ 4010⁽²⁾	960 2120	1480⁽²⁾ 3260⁽²⁾	780 1720	1260⁽²⁾ 2780⁽²⁾	650 1430	1010⁽²⁾ 2230⁽²⁾	620 1370	4.85 15.91
-0.5 m -2.0 ft			2060⁽²⁾ 4540⁽²⁾		2980⁽²⁾ 6570⁽²⁾	1660 3660	2310⁽²⁾ 5090⁽²⁾	1220 2690	1830⁽²⁾ 4030⁽²⁾	960 2120	1500⁽²⁾ 3310⁽²⁾	780 1720	1250⁽²⁾ 2760⁽²⁾	650 1430	1140⁽²⁾ 2510⁽²⁾	620 1370	4.64 15.22
-1.0 m -3.5 ft	2870⁽²⁾ 6330⁽²⁾		3670⁽²⁾ 8090⁽²⁾	2530 5580	2800⁽²⁾ 6170⁽²⁾	1670 3680	2200⁽²⁾ 4850⁽²⁾	1230 2710	1770⁽²⁾ 3900⁽²⁾	960 2120	1450⁽²⁾ 3200⁽²⁾	780 1720			1240⁽²⁾ 2730⁽²⁾	690 1520	4.34 14.24
-1.5 m -5.0 ft	3920⁽²⁾ 8640⁽²⁾		3260⁽²⁾ 7190⁽²⁾	2550 5620	2510⁽²⁾ 5530⁽²⁾	1680 3700	2000⁽²⁾ 4410⁽²⁾	1240 2730	1610⁽²⁾ 3550⁽²⁾	970 2140					1300⁽²⁾ 2870⁽²⁾	820 1810	3.92 12.86
-2.0 m -6.5 ft	3720⁽²⁾ 8200⁽²⁾		2590⁽²⁾ 5710⁽²⁾	2580 5690	2030⁽²⁾ 4480⁽²⁾	1710 3770	1610⁽²⁾ 3550⁽²⁾	1260 2780							1200⁽²⁾ 2650⁽²⁾		2.16 7.08

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 11
305D CR with a Long Stick, a 0.17 m³ (0.23 yd³) bucket, a 642 kg (1415 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							920⁽²⁾ 2030⁽²⁾
1.5 m 5.0 ft							1350⁽²⁾ 2980⁽²⁾	1180 2600
1.0 m 3.5 ft							1490 3280	1120 2470
0.5 m 2.0 ft							1450 3200	1080 2380
0					1960 4320	1420 3130	1420 3130	1060 2340
-0.5 m -2.0 ft			1910⁽²⁾ 4210⁽²⁾		1960 4320	1420 3130	1420 3130	1050 2310
-1.0 m -3.5 ft	2250⁽²⁾ 4960⁽²⁾		2900⁽²⁾ 6390⁽²⁾	2130 4700	1960 4320	1420 3130	1420 3130	1050 2310
-1.5 m -5.0 ft	3250⁽²⁾ 7170⁽²⁾		3120 6880	2150 4740	1980 4370	1430 3150	1420 3130	1060 2340
-2.0 m -6.5 ft	4410⁽²⁾ 9720⁽²⁾	4030 8880	3160 6970	2180 4810	2000 4410	1460 3220	1440 3170	1070 2360
-2.5 m -8.5 ft	3850⁽²⁾ 8490⁽²⁾		2500⁽²⁾ 5510⁽²⁾	2230 4920	1890⁽²⁾ 4170⁽²⁾	1490 3280	1450⁽²⁾ 3200⁽²⁾	1100 2430
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									650⁽²⁾ 1430⁽²⁾		3.87 12.70
4.0 m 13.0 ft			620⁽²⁾ 1370⁽²⁾						710⁽²⁾ 1570⁽²⁾	680 1500	4.32 14.17
3.5 m 11.5 ft			570⁽²⁾ 1260⁽²⁾		680⁽²⁾ 1500⁽²⁾	640 1410			740⁽²⁾ 1630⁽²⁾	580 1280	4.67 15.32
3.0 m 10.0 ft			610⁽²⁾ 1340⁽²⁾		680⁽²⁾ 1500⁽²⁾	630 1390			670 1480	510 1120	4.99 16.37
2.5 m 8.5 ft	660⁽²⁾ 1460⁽²⁾		700⁽²⁾ 1540⁽²⁾		730⁽²⁾ 1610⁽²⁾	630 1390	670 1480	510 1120	620 1370	470 1040	5.19 17.03
2.0 m 6.5 ft	860⁽²⁾ 1890⁽²⁾		830⁽²⁾ 1830⁽²⁾	760 1680	800 1760	610 1340	660 1460	500 1100	580 1280	440 970	5.32 17.45
1.5 m 5.0 ft	1110⁽²⁾ 2450⁽²⁾	920 2030	950 2100	730 1610	780 1720	600 1320	650 1430	490 1080	560 1240	430 950	5.39 17.69
1.0 m 3.5 ft	1160 2560	880 1940	930 2050	710 1570	760 1680	580 1280	640 1410	480 1060	560 1240	420 930	5.40 17.72
0.5 m 2.0 ft	1130 2490	850 1870	910 2010	690 1520	750 1650	570 1260	630 1390	480 1060	560 1240	420 930	5.34 17.52
0	1110 2450	830 1830	890 1960	680 1500	740 1630	560 1240	620 1370	470 1040	580 1280	440 970	5.22 17.13
-0.5 m -2.0 ft	1100 2430	820 1810	880 1940	670 1480	730 1610	550 1210			610 1340	460 1010	5.04 16.54
-1.0 m -3.5 ft	1090 2400	820 1810	880 1940	660 1460	730 1610	550 1210			670 1480	500 1100	4.77 15.65
-1.5 m -5.0 ft	1100 2430	820 1810	890 1960	670 1480					760 1680	580 1280	4.41 14.47
-2.0 m -6.5 ft	1110 2450	840 1850							930 2050	710 1570	3.91 12.83
-2.5 m -8.5 ft									1290 ⁽²⁾ 2840⁽²⁾	1010 2230	3.18 10.43

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 12
305D CR with a Long Stick, a 0.17 m³ (0.23 yd³) bucket, a 642 kg (1415 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							920⁽²⁾ 2030⁽²⁾
1.5 m 5.0 ft							1350⁽²⁾ 2980⁽²⁾	1310 2890
1.0 m 3.5 ft							1780⁽²⁾ 3920⁽²⁾	1260 2780
0.5 m 2.0 ft							2090⁽²⁾ 4610⁽²⁾	1220 2690
0					2240⁽²⁾ 4940⁽²⁾	1610 3550	2250⁽²⁾ 4960⁽²⁾	1190 2620
-0.5 m -2.0 ft			1910⁽²⁾ 4210⁽²⁾		3060⁽²⁾ 6750⁽²⁾	1610 3550	2300⁽²⁾ 5070⁽²⁾	1180 2600
-1.0 m -3.5 ft	2250⁽²⁾ 4960⁽²⁾		2900⁽²⁾ 6390⁽²⁾	2450 5400	2990⁽²⁾ 6590⁽²⁾	1610 3550	2270⁽²⁾ 5000⁽²⁾	1180 2600
-1.5 m -5.0 ft	3250⁽²⁾ 7170⁽²⁾		3860⁽²⁾ 8510⁽²⁾	2470 5450	2790⁽²⁾ 6150⁽²⁾	1630 3590	2150⁽²⁾ 4740⁽²⁾	1190 2620
-2.0 m -6.5 ft	4410⁽²⁾ 9720⁽²⁾		3330⁽²⁾ 7340⁽²⁾	2500 5510	2450⁽²⁾ 5400⁽²⁾	1650 3640	1920⁽²⁾ 4230⁽²⁾	1210 2670
-2.5 m -8.5 ft	3850⁽²⁾ 8490⁽²⁾		2500⁽²⁾ 5510⁽²⁾		1890⁽²⁾ 4170⁽²⁾	1680 3700	1450⁽²⁾ 3200⁽²⁾	1240 2730
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									650⁽²⁾ 1430		3.87 12.70
4.0 m 13.0 ft			620⁽²⁾ 1370⁽²⁾						710⁽²⁾ 1570⁽²⁾		4.32 14.17
3.5 m 11.5 ft			570⁽²⁾ 1260⁽²⁾		680⁽²⁾ 1500⁽²⁾				740⁽²⁾ 1630⁽²⁾	650 1430	4.67 15.32
3.0 m 10.0 ft			610⁽²⁾ 1340⁽²⁾		680⁽²⁾ 1500⁽²⁾				710⁽²⁾ 1570⁽²⁾	580 1280	4.99 16.37
2.5 m 8.5 ft	660⁽²⁾ 1460⁽²⁾		700⁽²⁾ 1540⁽²⁾		730⁽²⁾ 1610⁽²⁾	700 1540	770⁽²⁾ 1700⁽²⁾	570 1260	710⁽²⁾ 1570⁽²⁾	530 1170	5.19 17.03
2.0 m 6.5 ft	860⁽²⁾ 1890⁽²⁾		830⁽²⁾ 1830⁽²⁾		810⁽²⁾ 1790⁽²⁾	690 1520	810⁽²⁾ 1790⁽²⁾	570 1260	710⁽²⁾ 1570⁽²⁾	500 1100	5.32 17.45
1.5 m 5.0 ft	1110⁽²⁾ 2450⁽²⁾	1020 2250	980⁽²⁾ 2160⁽²⁾	820 1810	910⁽²⁾ 2010⁽²⁾	670 1480	870⁽²⁾ 1920⁽²⁾	560 1240	730⁽²⁾ 1610⁽²⁾	480 1060	5.39 17.69
1.0 m 3.5 ft	1360⁽²⁾ 3000⁽²⁾	990 2180	1140⁽²⁾ 2510⁽²⁾	800 1760	1020⁽²⁾ 2250⁽²⁾	650 1430	940⁽²⁾ 2070⁽²⁾	550 1210	760⁽²⁾ 1680⁽²⁾	480 1060	5.40 17.72
0.5 m 2.0 ft	1570⁽²⁾ 3460⁽²⁾	960 2120	1280⁽²⁾ 2820⁽²⁾	780 1720	1110⁽²⁾ 2450⁽²⁾	640 1410	1000⁽²⁾ 2200	540 1190	810⁽²⁾ 1790⁽²⁾	480 1060	5.34 17.52
0	1720⁽²⁾ 3790⁽²⁾	940 2070	1390⁽²⁾ 3060⁽²⁾	760 1680	1180⁽²⁾ 2600⁽²⁾	630 1390	1040⁽²⁾ 2290⁽²⁾	530 1170	880⁽²⁾ 1940⁽²⁾	490 1080	5.22 17.13
-0.5 m -2.0 ft	1790⁽²⁾ 3950⁽²⁾	930 2050	1450⁽²⁾ 3200⁽²⁾	750 1650	1220⁽²⁾ 2690⁽²⁾	620 1370			980⁽²⁾ 2160⁽²⁾	520 1150	5.04 16.54
-1.0 m -3.5 ft	1790⁽²⁾ 3950⁽²⁾	920 2030	1460⁽²⁾ 3220⁽²⁾	750 1650	1210⁽²⁾ 2670⁽²⁾	620 1370			1090⁽²⁾ 2400	570 1260	4.77 15.65
-1.5 m -5.0 ft	1710⁽²⁾ 3770⁽²⁾	930 2050	1390⁽²⁾ 3060⁽²⁾	750 1650					1150⁽²⁾ 2540⁽²⁾	650 1430	4.41 14.47
-2.0 m -6.5 ft	1520⁽²⁾ 3350⁽²⁾	940 2070							1220⁽²⁾ 2690⁽²⁾	790 1740	3.91 12.83
-2.5 m -8.5 ft									1290 ⁽²⁾ 2840⁽²⁾	1010 2230	3.18 10.43

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

305.5D CR

Show/hide table




Illustration 4	g00586902
(H) Height (F) Lifting capacity over the front of the machine (S) Lifting capacity over the side of the machine (R) Reach

Show/hide table

Table 13
305.5D CR with a Standard Stick, a 0.17 m³ (0.23 yd³) bucket, an 829 kg (1828 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft							1040⁽²⁾ 2290⁽²⁾
2.0 m 6.5 ft							1460⁽²⁾ 3220⁽²⁾	1340 2950
1.5 m 5.0 ft							1670 3680	1270 2800
1.0 m 3.5 ft							1620 3570	1220 2690
0.5 m 2.0 ft							1590 3500	1200 2650
0							1580 3480	1190 2620
-0.5 m -2.0 ft			1990⁽²⁾ 4390⁽²⁾		2190 4830	1600 3530	1580 3480	1190 2620
-1.0 m -3.5 ft	3090⁽²⁾ 6810⁽²⁾		3470 7650	2420 5340	2200 4850	1610 3550	1590 3500	1190 2620
-1.5 m -5.0 ft	4530⁽²⁾ 9990⁽²⁾	4490 9900	3480 7670	2430 5360	2210 4870	1620 3570	1600 3530	1200 2650
-2.0 m -6.5 ft	4700⁽²⁾ 10360⁽²⁾	4530 9990	3140⁽²⁾ 6920⁽²⁾	2460 5420	2240 4940	1650 3640	1620 3570	1220 2690
-2.5 m -8.5 ft			2140⁽²⁾ 4720⁽²⁾		1710⁽²⁾ 3770⁽²⁾	1690 3730
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									820⁽²⁾ 1810⁽²⁾		3.61 11.84
4.0 m 13.0 ft									880⁽²⁾ 1940⁽²⁾	850 1870	4.10 13.45
3.5 m 11.5 ft			810⁽²⁾ 1790⁽²⁾						920⁽²⁾ 2030⁽²⁾	730 1610	4.44 14.57
3.0 m 10.0 ft	810⁽²⁾ 1790⁽²⁾		860⁽²⁾ 1890⁽²⁾		900⁽²⁾ 1980⁽²⁾	710 1570			810 1790	630 1390	4.78 15.68
2.5 m 8.5 ft	990⁽²⁾ 2180⁽²⁾		960⁽²⁾ 2120⁽²⁾	860 1890	900 1980	700 1540			750 1650	580 1280	4.99 16.37
2.0 m 6.5 ft	1220⁽²⁾ 2690⁽²⁾	1050 2310	1080 2380	840 1850	890 1960	690 1520	740 1630	570 1260	710 1570	550 1210	5.13 16.83
1.5 m 5.0 ft	1310 2890	1010 2230	1060 2340	820 1810	870 1920	680 1500	730 1610	570 1260	680 1500	530 1170	5.20 17.06
1.0 m 3.5 ft	1270 2800	980 2160	1030 2270	800 1760	860 1890	660 1460	720 1590	560 1240	670 1480	520 1150	5.21 17.09
0.5 m 2.0 ft	1250 2760	950 2100	1020 2250	780 1720	840 1850	650 1430	710 1570	550 1210	680 1500	520 1150	5.15 16.90
0	1230 2710	940 2070	1000 2200	770 1700	830 1830	640 1410			700 1540	540 1190	5.03 16.50
-0.5 m -2.0 ft	1230 2710	930 2050	1000 2200	760 1680	830 1830	640 1410			740 1630	570 1260	4.84 15.88
-1.0 m -3.5 ft	1230 2710	930 2050	1000 2200	760 1680					820 1810	630 1390	4.56 14.96
-1.5 m -5.0 ft	1240 2730	940 2070	1000 2200	770 1700					940 2070	720 1590	4.18 13.71
-2.0 m -6.5 ft	1260 2780	960 2120							1180 2600	910 2010	3.65 11.98
-2.5 m -8.5 ft									1460⁽²⁾ 3220⁽²⁾	1410 3110	2.79 9.15

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 14
305.5D CR with a Standard Stick, a 0.17 m³ (0.23 yd³) bucket, an 829 kg (1828 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft							1040⁽²⁾ 2290⁽²⁾
2.0 m 6.5 ft							1460⁽²⁾ 3220⁽²⁾
1.5 m 5.0 ft							1980⁽²⁾ 4370⁽²⁾	1420 3130
1.0 m 3.5 ft							2370⁽²⁾ 5520⁽²⁾	1360 3000
0.5 m 2.0 ft							2550⁽²⁾ 5620⁽²⁾	1340 2950
0							2590⁽²⁾ 5710⁽²⁾	1330 2930
-0.5 m -2.0 ft			1990⁽²⁾ 4390⁽²⁾		3300⁽²⁾ 7280⁽²⁾	1810 3990	2560⁽²⁾ 5640⁽²⁾	1330 2930
-1.0 m -3.5 ft	3090⁽²⁾ 6810⁽²⁾		3780⁽²⁾ 8330⁽²⁾	2750 6060	3110⁽²⁾ 6860⁽²⁾	1810 3990	2460⁽²⁾ 5420⁽²⁾	1340 2950
-1.5 m -5.0 ft	4530⁽²⁾ 9990⁽²⁾		3720⁽²⁾ 8201⁽²⁾	2770 6110	2850⁽²⁾ 6280⁽²⁾	1830 4030	2280⁽²⁾ 5030⁽²⁾	1350 2980
-2.0 m -6.5 ft	4700⁽²⁾ 10360⁽²⁾		3140⁽²⁾ 6920⁽²⁾	2800 6170	2440⁽²⁾ 5380⁽²⁾	1850 4080	1960⁽²⁾ 4320⁽²⁾	1370 3020
-2.5 m -8.5 ft			2140⁽²⁾ 4720⁽²⁾		1710⁽²⁾ 3770⁽²⁾
Table Continued
(H)	3.5 m 11.5 ft		4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									820⁽²⁾ 1810⁽²⁾		3.61 11.84
4.0 m 13.0 ft									880⁽²⁾ 1940⁽²⁾		4.10 13.45
3.5 m 11.5 ft			810⁽²⁾ 1790⁽²⁾						920⁽²⁾ 2030⁽²⁾	800 1760	4.44 14.57
3.0 m 10.0 ft	810⁽²⁾ 1790⁽²⁾		860⁽²⁾ 1890⁽²⁾		900⁽²⁾ 1980⁽²⁾	790 1740			910⁽²⁾ 2010⁽²⁾	710 1570	4.78 15.68
2.5 m 8.5 ft	990⁽²⁾ 2180⁽²⁾		960⁽²⁾ 2120⁽²⁾		950⁽²⁾ 2100⁽²⁾	780 1720			900⁽²⁾ 1980⁽²⁾	650 1430	4.99 16.37
2.0 m 6.5 ft	1220⁽²⁾ 2690⁽²⁾	1160 2560	1100⁽²⁾ 2430⁽²⁾	930 2050	1040⁽²⁾ 2290⁽²⁾	770 1700	1020⁽²⁾ 2250⁽²⁾	640 1410	910⁽²⁾ 2010⁽²⁾	610 1340	5.13 16.83
1.5 m 5.0 ft	1490⁽²⁾ 3280⁽²⁾	1120 2470	1260⁽²⁾ 2780⁽²⁾	910 2010	1140⁽²⁾ 2510⁽²⁾	750 1650	1070⁽²⁾ 2360⁽²⁾	630 1390	940⁽²⁾ 2070⁽²⁾	590 1300	5.20 17.06
1.0 m 3.5 ft	1740⁽²⁾ 3840⁽²⁾	1090 2400	1420⁽²⁾ 3130⁽²⁾	890 1960	1240⁽²⁾ 2730⁽²⁾	740 1630	1130⁽²⁾ 2490⁽²⁾	620 1370	980⁽²⁾ 2160⁽²⁾	580 1280	5.21 17.09
0.5 m 2.0 ft	1910⁽²⁾ 4210⁽²⁾	1060 2340	1550⁽²⁾ 3420⁽²⁾	870 1920	1320⁽²⁾ 2910⁽²⁾	730 1610	1180⁽²⁾ 2600⁽²⁾	610 1340	1050⁽²⁾ 2310⁽²⁾	590 1300	5.15 16.90
0	2010⁽²⁾ 4430⁽²⁾	1050 2310	1630⁽²⁾ 3590⁽²⁾	860 1890	1380⁽²⁾ 3040⁽²⁾	720 1590			1140⁽²⁾ 2510⁽²⁾	600 1320	5.03 16.50
-0.5 m -2.0 ft	2030⁽²⁾ 4480⁽²⁾	1040 2290	1660⁽²⁾ 3660⁽²⁾	850 1870	1400⁽²⁾ 3090⁽²⁾	710 1570			1250⁽²⁾ 2760⁽²⁾	640 1410	4.84 15.88
-1.0 m -3.5 ft	1990⁽²⁾ 4390⁽²⁾	1050 2310	1630⁽²⁾ 3590⁽²⁾	850 1870					1310⁽²⁾ 2890⁽²⁾	700 1540	4.56 14.96
-1.5 m -5.0 ft	1850⁽²⁾ 4080⁽²⁾	1050 2310	1500⁽²⁾ 3310⁽²⁾	860 1890					1380⁽²⁾ 3042⁽²⁾	810 1790	4.18 13.71
-2.0 m -6.5 ft	1560⁽²⁾ 3440⁽²⁾	1070 2360							1440⁽²⁾ 3170⁽²⁾	1010 2230	3.65 11.98
-2.5 m -8.5 ft									1460⁽²⁾ 3220⁽²⁾		2.79 9.15

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 15
305.5D CR with a Long Stick, a 0.17 m³ (0.23 yd³) bucket, an 829 kg (1828 lb)counterweight and the Blade Up Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							1040⁽²⁾ 2290⁽²⁾		950⁽²⁾ 2100⁽²⁾
1.5 m 5.0 ft							1520⁽²⁾ 3350⁽²⁾	1290 2840	1220⁽²⁾ 2690⁽²⁾	1000 2200
1.0 m 3.5 ft							1620 3570	1220 2690	1260 2780	960 2120
0.5 m 2.0 ft							1570 3460	1170 2580	1230 2710	930 2050
0					2120 4670	1540 3400	1540 3400	1150 2540	1200 2650	910 2010
-0.5 m -2.0 ft			1990⁽²⁾ 4390⁽²⁾		2120 4670	1540 3400	1530 3370	1140 2510	1190 2620	900 1980
-1.0 m -3.5 ft	2390⁽²⁾ 5270⁽²⁾		2990⁽²⁾ 6590⁽²⁾	2320 5110	2130 4700	1540 3400	1530 3370	1140 2510	1190 2620	890 1960
-1.5 m -5.0 ft	3390⁽²⁾ 7470⁽²⁾		3380 7450	2330 5140	2140 4720	1560 3440	1540 3400	1150 2540	1190 2620	890 1960
-2.0 m -6.5 ft	4520⁽²⁾ 9970⁽²⁾	4370 9634	3410 7520	2360 5200	2160 4760	1580 3480	1560 3440	1160 2560	1200 2650	910 2010
-2.5 m -8.5 ft	5010⁽²⁾ 11050⁽²⁾	4440 9790	3110⁽²⁾ 6860⁽²⁾	2410 5310	2200 4850	1610 3550	1580 3480	1190 2620	1230 2710	930 2050
-3.0 m -10.0 ft			1870⁽²⁾ 4120⁽²⁾		1420⁽²⁾ 3130⁽²⁾
Table Continued
(H)	4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		5.5 m 18.0t		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									710⁽²⁾ 1570⁽²⁾		4.19 13.75
4.0 m 13.0 ft									750⁽²⁾ 1650	680 1500	4.59 15.06
3.5 m 11.5 ft			680⁽²⁾ 1500⁽²⁾						770 1700	590 1300	4.89 16.04
3.0 m 10.0 ft	640⁽²⁾ 1410⁽²⁾		710⁽²⁾ 1570⁽²⁾		740 1630	570 1260			680 1500	530 1170	5.20 17.06
2.5 m 8.5 ft	750⁽²⁾ 1650⁽²⁾		770⁽²⁾ 1700⁽²⁾	690 1520	740 1630	570 1260			630 1390	490 1080	5.40 17.72
2.0 m 6.5 ft	900⁽²⁾ 1980⁽²⁾	830 1830	870⁽²⁾ 1920⁽²⁾	680 1500	730 1610	560 1240			600 1320	460 1010	5.52 18.11
1.5 m 5.0 ft	1050 2310	810 1790	860 1890	660 1460	710 1570	550 1210	600 1320	460 1010	580 1280	440 970	5.59 18.34
1.0 m 3.5 ft	1020 2250	780 1720	840 1850	640 1410	700 1540	530 1170	590 1300	450 990	570 1260	430 950	5.59 18.34
0.5 m 2.0 ft	990 2180	760 1680	820 1810	620 1370	690 1520	520 1150			580 1280	440 970	5.54 18.18
0	970 2140	740 1630	810 1790	610 1340	680 1500	510 1120			590 1300	450 990	5.43 17.81
-0.5 m -2.0 ft	960 2120	730 1610	800 1760	600 1320	670 1480	510 1120			620 1370	470 1040	5.26 17.26
-1.0 m -3.5 ft	960 2120	720 1590	790 1740	600 1320					670 1480	510 1120	5.01 16.44
-1.5 m -5.0 ft	960 2120	720 1590	800 1760	600 1320					750 1650	570 1260	4.68 15.35
-2.0 m -6.5 ft	970 2140	740 1630							890 1960	680 1500	4.23 13.88
-2.5 m -8.5 ft									1180 2600	890 1960	3.60 11.81
-3.0 m -10.0 ft									1400⁽²⁾ 3090⁽²⁾		2.53 8.30

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.

Show/hide table

Table 16
305.5D CR with a Long Stick, a 0.17 m³ (0.23 yd³) bucket, an 829 kg (1828 lb)counterweight and the Blade Down Lifting Point in the Center of the Swing
(H)	All lifting capacities are in kilograms and pounds.⁽¹⁾
	(R)
	1.5 m 5.0 ft		2.0 m 6.5 ft		2.5 m 8.5 ft		3.0 m 10.0 ft		3.5 m 11.5 ft
	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)
4.5 m 15.0 ft
4.0 m 13.0 ft
3.5 m 11.5 ft
3.0 m 10.0 ft
2.5 m 8.5 ft
2.0 m 6.5 ft							1040⁽²⁾ 2290⁽²⁾		950⁽²⁾ 2100⁽²⁾
1.5 m 5.0 ft							1520⁽²⁾ 3350⁽²⁾	1430 3150	1220⁽²⁾ 2690⁽²⁾	1120 2470
1.0 m 3.5 ft							1990⁽²⁾ 4390⁽²⁾	1360 3000	1500⁽²⁾ 3310⁽²⁾	1080 2380
0.5 m 2.0 ft							2310⁽²⁾ 5090⁽²⁾	1320 2910	1730⁽²⁾ 3810⁽²⁾	1040 2290
0					2240⁽²⁾ 4940⁽²⁾	1740 3840	2480⁽²⁾ 5470⁽²⁾	1290 2840	1890 4170	1020 2250
-0.5 m -2.0 ft			1990⁽²⁾ 4390⁽²⁾		3090⁽²⁾ 6810⁽²⁾	1740 3840	2530⁽²⁾ 5580⁽²⁾	1280 2820	1970⁽²⁾ 4340⁽²⁾	1010 2230
-1.0 m -3.5 ft	2390⁽²⁾ 5270⁽²⁾		2990⁽²⁾ 6590⁽²⁾	2650 5840	3310⁽²⁾ 7300⁽²⁾	1750 3860	2510⁽²⁾ 5530⁽²⁾	1280 2820	1980⁽²⁾ 4370⁽²⁾	1000 2200
-1.5 m -5.0 ft	3390⁽²⁾ 7470⁽²⁾		4100⁽²⁾ 9040⁽²⁾	2670 5890	3110⁽²⁾ 6860⁽²⁾	1760 3880	2400⁽²⁾ 5290⁽²⁾	1290 2840	1920⁽²⁾ 4230⁽²⁾	1010 2230
-2.0 m -6.5 ft	4520⁽²⁾ 9970⁽²⁾		3840⁽²⁾ 8470⁽²⁾	2700 5950	2810⁽²⁾ 6190⁽²⁾	1780 3920	2200⁽²⁾ 4850⁽²⁾	1300 2870	1770⁽²⁾ 3900⁽²⁾	1020 2250
-2.5 m -8.5 ft	5010⁽²⁾ 11050⁽²⁾		3110⁽²⁾ 6860⁽²⁾	2750 6060	2330⁽²⁾ 5140⁽²⁾	1810 3990	1830⁽²⁾ 4030⁽²⁾	1330 2930	1420⁽²⁾ 3130⁽²⁾	1040 2290
-3.0 m -10.0 ft			1870⁽²⁾ 4122⁽²⁾		1420⁽²⁾ 3130⁽²⁾
Table Continued
(H)	4.0 m 13.0 ft		4.5 m 15.0 ft		5.0 m 16.5 ft		5.5 m 18.0t		Maximum Reach
(H)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	(F)	(S)	m ft
4.5 m 15.0 ft									710⁽²⁾ 1570⁽²⁾		4.19 13.75
4.0 m 13.0 ft									750⁽²⁾ 1650⁽²⁾		4.59 15.06
3.5 m 11.5 ft			680⁽²⁾ 1500⁽²⁾						790⁽²⁾ 1740⁽²⁾	660 1460	4.89 16.04
3.0 m 10.0 ft	640⁽²⁾ 1410⁽²⁾		710⁽²⁾ 1570⁽²⁾		770⁽²⁾ 1700⁽²⁾	640 1410			760⁽²⁾ 1680⁽²⁾	590 1300	5.20 17.06
2.5 m 8.5 ft	750⁽²⁾ 1650⁽²⁾		770⁽²⁾ 1700⁽²⁾		800⁽²⁾ 1760⁽²⁾	640 1410			750⁽²⁾ 1650⁽²⁾	540 1190	5.40 17.72
2.0 m 6.5 ft	900⁽²⁾ 1980⁽²⁾		870⁽²⁾ 1920⁽²⁾	760 1680	860⁽²⁾ 1890⁽²⁾	630 1390			760⁽²⁾ 1680⁽²⁾	520 1150	5.52 18.11
1.5 m 5.0 ft	1070⁽²⁾ 2360⁽²⁾	900 1980	980⁽²⁾ 2160⁽²⁾	740 1630	930⁽²⁾ 2050⁽²⁾	610 1340	910⁽²⁾ 2010⁽²⁾	510 1120	780⁽²⁾ 1720⁽²⁾	500 1100	5.59 18.34
1.0 m 3.5 ft	1240⁽²⁾ 2730⁽²⁾	870 1920	1100⁽²⁾ 2430⁽²⁾	720 1590	1010⁽²⁾ 2230⁽²⁾	600 1320	950⁽²⁾ 2100⁽²⁾	510 1120	810⁽²⁾ 1790⁽²⁾	490 1080	5.59 18.34
0.5 m 2.0 ft	1400⁽²⁾ 3090⁽²⁾	850 1870	1210⁽²⁾ 2670⁽²⁾	700 1540	1080⁽²⁾ 2380⁽²⁾	590 1300			850⁽²⁾ 1870⁽²⁾	490 1080	5.54 18.18
0	1520⁽²⁾ 3350⁽²⁾	830 1830	1290⁽²⁾ 2840⁽²⁾	690 1520	1140⁽²⁾ 2510⁽²⁾	580 1280			920⁽²⁾ 2030	510 1120	5.43 17.81
-0.5 m -2.0 ft	1600⁽²⁾ 3530⁽²⁾	820 1810	1350⁽²⁾ 2980⁽²⁾	680 1500	1160⁽²⁾ 2560⁽²⁾	570 1260			1010⁽²⁾ 2230⁽²⁾	530 1170	5.26 17.26
-1.0 m -3.5 ft	1620⁽²⁾ 3570⁽²⁾	810 1790	1360⁽²⁾ 3000⁽²⁾	680 1500					1130⁽²⁾ 2490⁽²⁾	570 1260	5.01 16.44
-1.5 m -5.0 ft	1570⁽²⁾ 3460⁽²⁾	820 1810	1290⁽²⁾ 2840⁽²⁾	680 1500					1190⁽²⁾ 2620⁽²⁾	640 2620	4.68 15.35
-2.0 m -6.5 ft	1420⁽²⁾ 3130⁽²⁾	830 1830							1260⁽²⁾ 2780⁽²⁾	760 1680	4.23 13.88
-2.5 m -8.5 ft									1340⁽²⁾ 2950⁽²⁾	1000 2200	3.60 11.81
-3.0 m -10.0 ft									1400⁽²⁾ 3090⁽²⁾		2.53 8.30

Show/hide table

⁽¹⁾	Lift capacities are based on "ISO 10567:2007" standards. The listed capacities do not exceed 87 percent of the hydraulic lifting capacity or 75 percent of the tipping capacity. Weight of all lifting accessories must be subtracted from the lifting capacities.
⁽²⁾	The lifting capacity is limited by the hydraulic capacity rather than the tipping load.