Lifting and Tying Down
`
S365C and S385C Demolition and Scrap Shears
[SEBU8485]
S365C and S385C Demolition and Scrap Shears
Transport Position - Transport of shear on host machine
S365C and S385C Demolition and Scrap Shears
Cutters - Inspect/Replace
SERVICE EQUIPMENT AND SUPPLIES
SHIPPING GP
S365C and S385C Demolition and Scrap Shears
Transport Position - Transport of shear on host machine
S365C and S385C Demolition and Scrap Shears
Lifting and Tying Down
1.1. Lifting the Shear
2.1. Tying Down the Shear
Show/hide table
| Weight of the Shear | ||
|---|---|---|
| Model | Weight | S/N Prefix |
| S2050 | |
LX2 |
| S3050 | |
LX3 |
| S2070 | |
LX4 |
| S3070 | |
LX5 |
| S2090 | |
SX7 |
| S3090 | |
SX8 |
Show/hide table
| |
| Illustration 1 | g06115100 |
|
(1) Lift Eye (2) Maintenance Eye (3) Lift Eye | |
Note: Do not use lifting point (2) to lift the shear. Only use this lifting point to lift the jaw.
There is one lifting point (1) at the rear of the shear, and two lifting points (3) on either side of the jaw. The lifting eye (2) on the moving jaw is for removing the moving jaw only. In order to lift the shear, use cables, chains, or straps that are certified for lifting.
Ensure rotation lock (if applicable) is installed on the shear. In order to tie down the shear, use cables, chains, or straps that are strong enough to secure the load. Use the lifting points to tie down the shear.
Information System:
S365C and S385C Demolition and Scrap Shears
Transport Position - Transport of shear on host machine
S365C and S385C Demolition and Scrap Shears
Operation
C13, C15, and C18 Tier 4 Interim Engines
Exhaust Balance Valve - Test
Product Link - PL522/523
General Information
S365C and S385C Demolition and Scrap Shears
Work Tool Installation and Removal
S365C and S385C Demolition and Scrap Shears
Declaration of Conformity
Product Link - PL522/523
Installation Parameters Configure
303.5E2, 304E2, 305E2 and 305.5E2 Mini Excavator Machine Systems
Track Carrier Roller - Remove and Install
C15 and C18 Tier 4 Final Engines
Engine Oil Pressure - Test
C9.3 Engines for Caterpillar Built Machines
Sensor Calibration Required - Test
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators
Lifting Capacities
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Front Idler - Remove and Install
Product Link - PL522/523
Diagnostic Capabilities
C27 and C32 Generator Set Engines
Fuel Lines - Remove and Install
S365C and S385C Demolition and Scrap Shears
Cutters - Inspect/Replace
S365C and S385C Demolition and Scrap Shears
Cutting Edge Bolts - Tighten
S365C and S385C Demolition and Scrap Shears
Jaw - Repair
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 23
312D and 313D Excavators Machine System Specifications
Control Valve - Two Pump One Way Flow
312D and 313D Excavators Machine System Specifications
Front Lines
349E Excavator Hydraulic System
Solenoid Valve (Fine Swing) - If Equipped
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 20
Product Link - PL522/523
Event Code List
Product Link - PL522/523
Electronic Service Tool Does Not Communicate with ECM