Rotator Head Bolts - Inspect
`
S365C and S385C Demolition and Scrap Shears
[SEBU8485]
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Check
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Replace
HYDRAULIC SYSTEM
ROTATOR GP
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Check
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Inspect
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Replace
- Position the work tool in an upright position just above the ground.
- Stop the machine engine in order to prevent inadvertent movement of the work tool.
Note: The host machine must be equipped with a boom lowering control valve in order to perform this procedure. If the host machine is not equipped with a boom lowering control valve, contact your Cat dealer.
- Check the rotator head bolts (2) on the outer ring (1). If any bolts are missing the heads, replace all the bolts (2) in the outer ring (1) .
ReferenceFor more information on replacing the rotator head bolts, refer to Operation and Maintenance Manual, "Rotator Head Bolts - Replace" for the work tool that is being serviced.
Show/hide table
 | |
| Illustration 1 | g02174758 |
- Remove bolts (5) and washers (4). Remove cover plate (3) .
Show/hide table
 | |
| Illustration 2 | g02174775 |
- Cover plate (3) must be removed in order to access rotator head bolts (6) in the inner ring (7). Only a few bolts will be accessible at a time.
Show/hide table
 | |
| Illustration 3 | g02190813 |
- Check rotator head bolts (6) in the inner ring (7). If any bolts are missing the heads, replace all the bolts (6) in the inner ring (7) .
Note: The work tool can be rotated manually in order to view all of the rotator head bolts. Use a sufficiently long lever in order to rotate the work tool.
ReferenceFor more information on replacing the rotator head bolts, refer to Operation and Maintenance Manual, "Rotator Head Bolts - Replace" for the machine that is being serviced.
- Install cover plate (3) .
- Install washers (4) and bolts (5) .
Information System:
362-4250 Deck Height Measuring Tool{1201}
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Check
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System
MID 039 - CID 2429 - FMI 06
2010/07/21
The Stick Support Pin Is Improved on Certain Small Excavators {6501}
450F Backhoe Loader Hydraulic and Steering System
Control Valve (Boom) (Mechanically Operated)
312D and 313D Excavators Machine System Specifications
Stick Cylinder
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators
Safety Messages
450F Backhoe Loader Hydraulic and Steering System
Control Valve (Extendable Stick) (Mechanically Operated)
320E and 323E Excavators
Engine Oil and Filter - Change
320E and 323E Excavators
Engine Oil Level - Check
2010/06/25
A New Multi Combined Function - Work Tool Valve (MCV) is Now Used on Certain Wheeled Excavators {5064}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units
Joystick Controls Alternate Patterns - If Equipped
S365C and S385C Demolition and Scrap Shears
Rotator Head Bolts - Replace
S365C and S385C Demolition and Scrap Shears
Wear Plates - Inspect/Replace
2010/07/08
New AccuGrade Software Version 11.21 for the CD700 Display Is Now Available on SISweb {7220, 7620}
Capturing Photo, Video, or Audio Evidence of Machine Issues {0336, 1000, 7000}
450E Backhoe Loader Machine Electronic Control System
Electrical Connector - Inspect
349F and 352F Excavators Hydraulic System
Swing Drive
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators
Operator Controls
349F and 352F Excavators Hydraulic System
Bypass Valve (Return) - Bypass Check Valve
242-3567 Variable Crimp Die Bowl{0684}
349E Excavator Machine Electronic Control System
System Operation
2010/07/08
Correction to Operation and Maintenance Manual , "Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace" {7320, 7342}
349E Excavator Hydraulic System
Travel Parking Brake