Installation of the 360-6218 Electronic Control Wiring Gp on Certain Hydraulic Excavators {1408} Caterpillar

Installation of the 360-6218 Electronic Control Wiring Gp on Certain Hydraulic Excavators {1408} [M0067298]

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Installation of the 360-6218 Electronic Control Wiring Gp on Certain Hydraulic Excavators {1408}

1.1. Introduction

2.1. Safety Section

3.1. Required Parts

4.1. Installation Procedure

Excavator
374F (S/N: AT21-UP; AP41-UP; NFJ1-UP; MFL1-UP; DNM1-UP)
390F (S/N: HJD1-UP; TYE1-UP; MGF1-UP; HSM1-UP; GAY1-UP)
Hydraulic Control
HYDRAULIC KIT (S/N: HKF1-UP)
Material Handler
390F MHPU (S/N: B371-UP)

Introduction

Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.

Safety Section

Show/hide table

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.

Show/hide table




Illustration 1	g00104545

Prevent the machine from movement. Park the machine on a level surface.

Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your AVSpare dealer.

Required Parts

Show/hide table

Table 1
360-6218 Electronic Control Wiring Gp (- 02)
Item	Qty	Part No.	Part Name
(1)	2	111-4836	Clip
(2)	2	116-0118	Clip
(3)	1	369-0024	Wiring Harness
(4)	1	432-6274	Platform Harness As
(5)	1	163-6795	Cable Strap
(6)	10	3S-2093	Cable Strap
(7)	1	7X-2621	Bolt
(8)	3	8T-4121	Hard Washer
(9)	2	8T-4137	Bolt

Show/hide table




Illustration 2	g06026264
Overview of the 360-6218 Electronic Control Wiring Gp

Installation Procedure

Show/hide table




Illustration 3	g06026270
View from under the cab showing left-hand electric pedal connection. (GE-C2) Connect to Electric Pedal - Left-Hand "J850 WH", "235 BK", "N794 GY" (GE-C3) When using Electric Pedal - Right-Hand connection"J850 WH", "235 BK", "N795 WH" (1) 111-4836 Clip (4) 432-6274 Platform Harness As (8) 8T-4121 Hard Washer (9) 8T-4137 Bolt

Install wiring and connectors as shown.

Note: Wiring can be installed to use an electric pedal on either the right-hand side or the left-hand side.

Show/hide table




Illustration 4	g06026298
(GE-C1) Connect to Harness (12 Poles), "J850 WH", "235 BK", "N794 GY", "J850 WH", "235 BK", "N795 WH" (1) 111-4836 Clip (4) 432-6274 Platform Harness As (6) 3S-2093 Cable Strap (8) 8T-4121 Hard Washer (9) 8T-4137 Bolt

Route harness (4) and connect on the right-hand side under the cab as shown.

Show/hide table




Illustration 5	g06026336
View from left-hand side of the cab with panels removed to show harness routing. (GA-C3) Connect to Harness (12 Poles), "J850 WH", "235 BK", "N794 GY", "J850 WH", "235 BK", "N795 WH" (GA-C1) Connect to Harness (6 Poles), "J850 WH", "235 BK", "N794 GY", "N795 WH" (3) 369-0024 Wiring Harness (5) 163-6795 Cable Strap (6) 3S-2093 Cable Strap