Installation of the <NOBR>504-7558</NOBR> Coupler Control Ar on Certain Hydraulic Excavators {1408, 5057, 6129} Caterpillar


`
Installation of the <NOBR>504-7558</NOBR> Coupler Control Ar on Certain Hydraulic Excavators {1408, 5057, 6129} [M0067862]
WORK TOOLS
COUPLER GP-QUICK
Installation of the <NOBR>504-7558</NOBR> Coupler Control Ar on Certain Hydraulic Excavators {1408, 5057, 6129}
1.1. Introduction
2.1. Safety Section
3.1. Required Parts
4.1. Reference Section
Excavator
323D2 (S/N: XBK1-UP)
Hydraulic Kit
HYDRAULIC KIT (S/N: HKD1-UP)

Introduction

Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.

Reference: Service Guide, SEBD0512, "AVSpare Service Welding Guide"

Reference: Special Instruction, REHS1841, "General Welding Procedures"

Reference: Torque Specifications, SENR3130, "Torque Specifications"

Safety Section



Illustration 1g00104545

Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your AVSpare dealer.

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.


------ WARNING! ------

Personal injury or death can result from improperly checking for a leak.

Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.

If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.


------ WARNING! ------

Personal injury or death can result from sudden work tool movement.

Sudden movement of the work tool can cause injury to persons near the work tool.

To prevent injury or death, make sure that the area around the work tool is clear of personnel and obstructions before operating the work tool.


------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.


------ WARNING! ------

Personal injury can result from flame cutting or welding on painted areas.

The effect of gasses from burned paint is a hazard to the person doing the cutting or welding.

Do not flame cut or weld on painted areas.



NOTICE

Before carrying out arc welding on the machine or on any equipment attached to the machine, disconnect all power and ground leads from the batteries in order to avoid possible damage to electronic components.


Required Parts

Table 1
504-7558 Coupler Control Ar"Revision - 00" 
Qty  Part No.  Description  Media 
(1)  268-6816  Film Gp 
(1)  376-6329  Front Lines Gp  M0067864 
(1)  494-6809  Chassis Wiring Gp  M0067866 
(1)  494-6811  Cab Wiring Gp  M0067868 
(1)  343-8342  Hydraulic Lines Kit  REHS3854 

Reference Section

Reference: Test and Adjust, KENR9976, "Process For Setting Up the Work Tool".

Information System:

336D 2L and 340D 2L Excavators Machine Systems Stick Bearings and Seals - Remove and Install
314F and 315F Excavators Machine System Specifications Pilot Lines
Electric Starting Motor on Certain C7.1 Machine Engines {1453}
314F and 315F Excavators Machine System Specifications Pilot Valve
314F and 315F Excavators Machine System Specifications Pilot Valve
314F and 315F Excavators Machine System Specifications Pilot Lines
Buttons are Now Used When Installing Bonded Glass {7301}
Four-point Seat Belts are Now Available for Certain Excavators and Track Feller Bunchers {7312}
374F Excavator Machine Systems Main Hydraulic Pump - Assemble
374F Excavator Machine Systems Main Hydraulic Pump - Disassemble
349D2 MHPU Mobile Hydraulic Power Unit (OEM) Maintenance Interval Schedule
336D 2L and 340D 2L Excavators Machine Systems Stick - Remove and Install
Installation Procedure for the <NOBR>376-6329</NOBR> Front Lines Gp on Certain Hydraulic Excavators {5057}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
Installation Procedure for the <NOBR>494-6809</NOBR> Chassis Wiring Gp On Certain Hydraulic Excavators {1408, 6129}
Installation Procedure for the <NOBR>494-6811</NOBR> Cab Wiring Gp On Certain Hydraulic Excavators {1408, 7301}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Cylinder Head
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Camshaft
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Piston and Rings
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Gear Group (Front)
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Glow Plugs
330F MHPU Mobile Hydraulic Power Unit Machine System Engine Performance - Test - Engine Speed
325F Excavator Machine Systems Sprocket - Remove and Install