Installation Procedure for the 260-8007 Front Lines Group {5057} Caterpillar

Installation Procedure for the 260-8007 Front Lines Group {5057} [GEHS0046]

HYDRAULIC SYSTEM

LINES GP-FRONT

Installation Procedure for the 260-8007 Front Lines Group {5057}

1.1. Introduction

2.1. Safety Section

3.1. Required Parts

4.1. Installation Procedure

Excavator:
320D (S/N: FNA1-UP)
320D (S/N: DFB1-UP; MDE1-UP; A6F1-UP; A8F1-UP; A9F1-UP; KGF1-UP; MGG1-UP; MCH1-UP; TDH1-UP; DHK1-UP; FAL1-UP; KLM1-UP; SPN1-UP; WJN1-UP; BWP1-UP; GDP1-UP; AZR1-UP; SNS1-UP; EBT1-UP; PHX1-UP; CXY1-UP; BWZ1-UP; JFZ1-UP; JGZ1-UP)
323D (S/N: PBE1-UP; LFL1-UP)
Work Tool:
HYDRAULIC KIT (S/N: HKD1-UP)

Introduction

This Special Instruction provides the information that is necessary to install the 260-8007 Front Lines Gp on certain excavators.

Safety Section

Show/hide table




Illustration 1	g00104545

Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your AVSpare dealer.

Note: Drain the hydraulic fluid from the hydraulic tank before opening the hydraulic system. Remember to fill the hydraulic tank with hydraulic fluid once the installation is complete.

Show/hide table

NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before operating any compartment or disassembling any component containing fluids. After collecting all fluids in suitable containers, dispose of all fluids according to local regulations and mandates.

Show/hide table

Check valves in the hydraulic system may allow pressure to exist in the hydraulic lines after the engine has been stopped. Pressure must be relieved prior to servicing the components of the hydraulic system. Failure to relieve pressure prior to servicing may result in personal injury.

Show/hide table

Personal injury or death can result from improperly checking for a leak.
Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.

If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.

Show/hide table

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

Required Parts

Show/hide table

Table 1
Required Parts 260-8007 Front Lines Gp Revision -10
Item	Qty	Part Number	Description
(1)	1	7Y-3731	Flange
(2)	1	102-1248	Hose As
(3)	4	105-3477	Bolt
(4)	1	173-4664	Flange
(5)	1	177-2653	Relief Valve Gp
(6)	1	207-6222	Block
(7)	2	212-5148	Block
(8)	1	218-1139	Block
(9)	1	260-7872	Support As
(10)	1	260-8043	Block
(11)	1	266-0912	Bracket
(12)	1	266-0913	Support As
(13)	1	266-1217	Hose As
(14)	1	266-1278	Block
(15)	1	266-1279	Flange
(16)	1	266-1303	Hose As
(17)	1	275-1439	Block
(18)	1	296-7067	Support As
(19)	1	296-7069	Support As
(20)	1	317-4712	Hose As
(21)	1	325-8865	Support As
(22)	2	099-8232	O-Ring Seal
(23)	4	101-7397	Bolt
(24)	4	101-7401	Bolt
(25)	4	101-7402	Bolt
(26)	4	101-7404	Bolt
(27)	1	148-8323	Connector As
(28)	1	148-8330	Connector As
(29)	1	148-8347	Elbow As
(30)	1	148-8352	Elbow As
(31)	1	148-8355	Elbow As
(32)	1	148-8411	Plug
(33)	1	148-8429	Tee As
(34)	1	153-6237	Elbow As
(35)	2	164-4180	Plug As
(36)	3	1P-3702	Rectangular Seal
(37)	4	1P-3703	Rectangular Seal
(38)	4	280-2747	Bolt
(39)	2	5K-9090	O-Ring Seal
(40)	2	5P-7468	Clip
(41)	2	5P-7469	Clip
(42)	2	5P-8444	Grommet
(43)	2	6V-1874	Grommet
(44)	8	8T-4121	Hard Washer
(45)	6	8T-4136	Bolt
(46)	4	8T-4176	Bolt
(47)	8	8T-4183	Bolt
(48)	2	8T-4196	Bolt
(49)	26	8T-4223	Hard Washer
(50)	6	8T-4956	Bolt
(51)	8	8T-5092	Bolt

Show/hide table




Illustration 2	g03332754
260-8007 Front Lines Gp