PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS
[REBE1656]
FRAME AND BODY
FRAME GP
PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS
REBE1656-00
Show/hide table
| 07Mar2007 |
U-87
A-73
D-72
O-81
Show/hide table
| Before/After | PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS |
|
| 7063 7050 | PS42358 |
|
Show/hide table
| NOTE: | This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS42358" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code. |
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst. |
Show/hide table
Show/hide table
TERMINATION DATE |
| 31Mar2009 |
PROBLEM
Show/hide table
| The service life of the ball joint may not be as long as desired on certain BA18 Angle Brooms. A new ball joint is available that has a greater ball retention capabiliity. |
AFFECTED PRODUCT
Show/hide table
| Model | Identification Number |
| BA18 | AZN00901-00904, 906-911, 913-914, 917-933, 935-943, 945-948, 950-955, 957-967, 969-974, 976-1020, 1022-1035, 1037, 1039-1056, 1058-1063, 1065-1070, 1072-1082, 1084-1090, 1092-1106, 1108-1130, 1132-1137, 1139-1144, 1146-1165, 1167-1207, 1210-1212, 1214-1227, 1229-1242, 1244, 1246-1247, 1249-1251, 1253-1255, 1258-1262, 1264, 1266-1269, 1272, 1274-1278, 1280-1286, 1288-1292, 1294-1295, 1297-1299, 1301-1302, 1305-1306, 1309-1314, 1316, 1318-1319, 1321-1335, 1339-1345, 1350-1352, 1354, 1356-1359, 1361-1364, 1366, 1368-1393, 1395-1418, 1420-1422, 1424-1433, 1438-1441, 1443, 1445, 1447-1449, 1451, 1453-1454, 1457-1466, 1470-1473, 1475, 1477, 1479, 1483-1485, 1491, 1493, 1495-1499, 1503, 1505-1506, 1510-1513, 1515, 1517, 1519-1522, 1524-1526, 1528, 1530, 1537, 1544-1545, 1548, 1556, 1558, 1565-1567, 1572-1575, 1578-1581, 1583-1585, 1587-1594, 1597-1599, 1602-1603, 1605-1606, 1609-1611, 1616-1619, 1621, 1623, 1627, 1629-1631, 1633-1634 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
| 2 | 5D4412 | FITTING |
| 8 | 6V7687 | LOCKNUT |
| 8 | 8T4184 | BOLT |
| 16 | 8T4223 | WASHER-HARD |
| 2 | 3072665 | BALL JOINT |
ACTION REQUIRED
Show/hide table
| Refer to the attached Rework Procedure. |
Show/hide table
SERVICE CLAIM ALLOWANCES
Show/hide table
0-24 mo |
||||||
Show/hide table
| NOTE: This is a 1.0-hour job | ||||||
Show/hide table
PARTS DISPOSITION
Show/hide table
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
Show/hide table
| Position the angle broom in the storage position with the stands supporting the broom bristles and the machine interface centered and lowered to the ground. Block up the back of the front frame group to ensure the bristles and core assembly are securely supported prior to disassembly. |
|
| Image1.1.1 |
|
| Image1.1.2 |
| Remove the 4 bolts securing the ball joint to the frame assembly. |
|
| Image1.2.1 |
| Remove the cotter pin and nut from the lower part of the top ball joint. |
|
| Image1.3.1 |
| Replace the old ball joint with a 307-2665 Ball Joint and install a 45 degree grease fitting to the new ball joint. The grease fitting should point up. Install new 8T-4184 Bolts, 8T-4223 Washers, and 6V-7687 Nuts. Tighten the bolts to a torque of 105 +/- 20 Nm. Tighten the castle nut to a torque of 170 +/- 25 Nm. Tighten the castle nut no more then one castellation and install the cotter pin to keep the nut from coming loose. |
| Repeat procedure with the lower ball joint ensuring the hardware is installed as per the image above. Grease each ball joint. One to two pumps is sufficient. |
Information System:
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING AN ADDITIONAL STEP TO IMPROVE ACCESS ON CERTAIN 330D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS
PRODUCT SUPPORT PROGRAM FOR REPLACING AND INSTALLING HEATING, VENTILATION, AND AIR CONDITIONING COMPONENTS ON CERTAIN 320C, 322C, 325C, 330C FORESTRY EXCAVATORS AND 511, 521, 522, 532, 541, 551, 552, TK711, TK721, TK722, TK732, TK741, TK751, TK752, 1
Product Support Program For Reworking Track Link Assemblies On Certain 365CL, 365CL FS, 365CL MH, 385C, 385CL, 385C FS, And 385CL MH Hydraulic Excavators
PRODUCT IMPROEVMENT PROGRAM FOR REPLACING THE FUEL RETURN LINE ON CERTAIN 330D(L) EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING 149-2356, 149-3253, 149-3254, 149-3255, 200-6198, AND 225-9217 CONTROL GROUPS FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REPAIRING THE SINGLE TILT LOADER LIFT ARM ON CERTAIN 416D, 420D, 424D AND 428D BACKHOE LOADERS
PRODUCT SUPPORT PROGRAME TO REPLACE MOTOR MOUNTING BOLTS ON CERTAIN BU115 AND BU118 UTILITY BROOMS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 0R4274, 0R4275, 0R4278, 0R9355, 0R4277, 0R4279, AND 0R9360 LONG BLOCKS FROM DEALER PART STOCK
PRODUCT SUPPORT PROGRAM FOR REPLACING THE EXTENDABLE STICK CYLINDER TUBE ASSEMBLY ON CERTAIN 416E, 420E, AND 430E BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM TO REMOVE STABILITY ALARM SWITCH ON CERTAIN 325D, 330D, 345C, AND 385CL EXCAVATORS (DEMOLITION CORE)
Product Improvement Program For Inspecting The Swing Outer Bolt On Certain 345C Excavators
Product Improvement Program For Replacing Stems In The Machine Control Valve On Certain 318C, 320C, 320D, 320D RR, 321C CR, 325D, And 330D Excavators
PRODUCT SUPPORT PROGRAM FOR REWORKING BOOM FOOT CRACKING ON CERTAIN 315B AND 315C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE LOAD CONTROL VALVE GROUP ON CERTAIN 301.6C AND 301.8C MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW MACHINE SOFTWARE ON CERTAIN 365CL, 365CL FS, 365CL MH, 385C, 385CL, 385CL MH AND 385C FS EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW MACHINE SOFTWARE ON CERTAIN 420E 430E 432E 434E 442E 444E BACKHOE LOADERS EQUIPPED WITH AN AUTOSHIFT TRANSMISSION
PRODUCT SUPPORT PROGRAM FOR INSTALLING WASHERS TO THE EXTENDABLE STICK CYLINDER PIN RETENTION GROUP ON CERTAIN 416E, 420E, AND 430E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE GOVERNOR CABLE ON CERTAIN 301.6C, 301.8C AND 302.5C MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACEMENT OF GET PINS, ADAPTERS, AND TIPS ON CERTAIN 303CCR, 303.5CCR, 304CCR, 305CCR MINI-HYDRAULIC EXCAVATORS
Product Support Program to Install A New Governor Spring On Certain 301.6C And 301.8C Mini Hydraulic Excavators
PRODUCT SUPPORT PROGRAM FOR REWORKING THE SINGLE TILT LOADER ARMS THAT MAY CRACK ON CERTAIN 416D, 420D, 430D, 416E, 420E, AND 430E BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE DRIVE GROUPS FOR THE TRAVEL SYSTEM ON CERTAIN 311C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE LOW PRESSURE FUEL RETURN LINE HOSE TO MEDIUM PRESSURE FUEL RETURN LINE HOSE ON CERTAIN 345B AND 345B SERIES II EXCAVATORS