Product Support Program to Install A New Governor Spring On Certain 301.6C And 301.8C Mini Hydraulic Excavators
[REBE1703]
FUEL SYSTEM
Product Support Program to Install A New Governor Spring On Certain 301.6C And 301.8C Mini Hydraulic Excavators
REBE1703-00
Show/hide table
| 11Jun2007 |
U-245
A-200
D-210
O-226
Show/hide table
| After Failure Only | PRODUCT SUPPORT PROGRAM TO INSTALL A NEW GOVERNOR SPRING ON CERTAIN 301.6C AND 301.8C MINI HYDRAULIC EXCAVATORS |
|
| 1264 | PS51311 |
|
Show/hide table
| NOTE: | This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS51311" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code. |
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst. |
Show/hide table
Show/hide table
TERMINATION DATE |
| 30Jun2009 |
PROBLEM
Show/hide table
| The engine speed can fluctuate (hunt) on certain 301.6C and 301.8C Mini Hydraulic Excavators. This is due to governor instability. Every machine does not exhibit this problem. When the problem does occur, it occurs at low hours when the engine is new. |
AFFECTED PRODUCT
Show/hide table
| Model | Identification Number |
| 301.6C | JBB00301-00948, 950-960 |
| 301.8C | JSB00303-01718 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
| 1 | 2230341 | GASKET |
| 1 | 2464235 | C-RING |
| 1 | 2464238 | COVER-HIGH SPEED |
| 1 | 3012372 | BOLT AS |
| 1 | 3012373 | SPRING-GOVERNOR |
ACTION REQUIRED
Show/hide table
| Replace the 223-0336 Governor Spring with a 301-2373 Governor Spring. You will need to remove the tamperproof cap and set the high idle speed. The procedure for installing the new governor spring and for setting the high idle speed is described in Special Instruction, REHS3356. |
Show/hide table
SERVICE CLAIM ALLOWANCES
Show/hide table
Show/hide table
| NOTE: This is a 1.0-hour job | ||||||
Show/hide table
PARTS DISPOSITION
Show/hide table
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
Information System:
PRODUCT SUPPORT PROGRAM FOR REPLACEMENT OF GET PINS, ADAPTERS, AND TIPS ON CERTAIN 303CCR, 303.5CCR, 304CCR, 305CCR MINI-HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE GOVERNOR CABLE ON CERTAIN 301.6C, 301.8C AND 302.5C MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING WASHERS TO THE EXTENDABLE STICK CYLINDER PIN RETENTION GROUP ON CERTAIN 416E, 420E, AND 430E BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW MACHINE SOFTWARE ON CERTAIN 420E 430E 432E 434E 442E 444E BACKHOE LOADERS EQUIPPED WITH AN AUTOSHIFT TRANSMISSION
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW MACHINE SOFTWARE ON CERTAIN 365CL, 365CL FS, 365CL MH, 385C, 385CL, 385CL MH AND 385C FS EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE LOAD CONTROL VALVE GROUP ON CERTAIN 301.6C AND 301.8C MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING BOOM FOOT CRACKING ON CERTAIN 315B AND 315C EXCAVATORS
Product Improvement Program For Replacing Stems In The Machine Control Valve On Certain 318C, 320C, 320D, 320D RR, 321C CR, 325D, And 330D Excavators
PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING AN ADDITIONAL STEP TO IMPROVE ACCESS ON CERTAIN 330D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE BALL JOINTS ON CERTAIN BA18 ANGLE BROOMS
PRODUCT SUPPORT PROGRAM FOR REPLACING AND INSTALLING HEATING, VENTILATION, AND AIR CONDITIONING COMPONENTS ON CERTAIN 320C, 322C, 325C, 330C FORESTRY EXCAVATORS AND 511, 521, 522, 532, 541, 551, 552, TK711, TK721, TK722, TK732, TK741, TK751, TK752, 1
PRODUCT SUPPORT PROGRAM FOR REWORKING THE SINGLE TILT LOADER ARMS THAT MAY CRACK ON CERTAIN 416D, 420D, 430D, 416E, 420E, AND 430E BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE DRIVE GROUPS FOR THE TRAVEL SYSTEM ON CERTAIN 311C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE LOW PRESSURE FUEL RETURN LINE HOSE TO MEDIUM PRESSURE FUEL RETURN LINE HOSE ON CERTAIN 345B AND 345B SERIES II EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE TOPS CANOPY ON CERTAIN 304 CR AND 305 CR MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE TOPS CANOPY ON CERTAIN 303 CR MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE CYLINDER GROUP ON CERTAIN G315B AND VRG25/2 DEMOLITION AND SORTING GRAPPLES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE HYDRAULIC ROTATOR ON CERTAIN GSH15 GRAPPLES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 4B-1283 SCREWS FOR THE CAB DOOR GROUP ON CERTAIN 320C HW, 320C ST, 320D HD/LC, 320D HEEL, 320D HW, 322C HW, 322C LGP, 322C ST, 324D, 324D HEEL, 325C HW, 325C ST, 325D, 325D BUTT N, 325D HEEL, 330C HW, 330C ST
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 270-9726 DOOR GROUP AND 271-0040 SUPPORT ASSEMBLY ON CERTAIN 328D CR EXCAVATORS
PRODUCT SUPPORT PROGRAM TO ADJUST AND PROTECT THE SIDESHIFT AND BACKHOE HOSES ON CERTAIN 428E NARROW FRAME BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE FRONT AXLE PIVOT PIN LOCK ON CERTAIN M313D, M313D, M315C, M315D, M316C, M316D, M318C & M318D WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE HYDRAULIC ROTATOR ON CERTAIN GSH20 GRAPPLES