EPC Parts Catalogs

PRODUCT SUPPORT PROGRAM FOR REWORKING THE FRAME ON CERTAIN PW2708-H QUICK COUPLERS WITH PREFIX CJE AND DDK (P/N 193-8526 AND 216-1270) Caterpillar


  1. Home
  2. Service Letter-NACD
  3. #2510
`
PRODUCT SUPPORT PROGRAM FOR REWORKING THE FRAME ON CERTAIN PW2708-H QUICK COUPLERS WITH PREFIX CJE AND DDK (P/N 193-8526 AND 216-1270) [REBE4767]
WORK TOOL ARRANGEMENT
COUPLER AR
PRODUCT SUPPORT PROGRAM FOR REWORKING THE FRAME ON CERTAIN PW2708-H QUICK COUPLERS WITH PREFIX CJE AND DDK (P/N 193-8526 AND 216-1270)
REBE4767-00

Show/hide table
03Apr2009


U-131
O-114

 
Show/hide table
After Failure Only
  
  

PRODUCT SUPPORT PROGRAM FOR REWORKING THE FRAME ON CERTAIN PW2708-H QUICK COUPLERS WITH PREFIX CJE AND DDK (P/N 193-8526 AND 216-1270)
6129
PS51644
Show/hide table
NOTE:

This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS51644" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.

Show/hide table
NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst.
Show/hide table
Show/hide table

Show/hide table

TERMINATION DATE
30Apr2010

PROBLEM

Show/hide table
The existing AVSpare PW2708-H Quick Coupler frame can interfere with original Volvo Work Tools on certain horizontal pin lock Quick Couplers. The Work Tool can not be attached and locked if the Quick Coupler interferes with the Work Tool.

AFFECTED PRODUCT

Show/hide table
Model Identification Number
PW 2708 CJE00101-00127

DDK00101-00107

PARTS NEEDED

Show/hide table

Qty

 Part Number Description
6 8T4121 WASHER-HARD
6 8T4133 NUT
6 8T4182 BOLT-HEX HEAD
6 1591118 LOCKWASHER-DISC
1 3391760 COVER AS
2 PLATE DEALER FABRIAVSED PLATE
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 4% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table
Rework Quick Coupler frame. Refer to Special Instruction REHS3877 for rework instructions.
Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table
Product smu/age whichever comes first
AVSpare
Dealer Suggested
Customer Suggested
Parts %
Labor Hrs%
Parts %
Labor Hrs%
Parts %
Labor Hrs%
0-6000 hrs,
0-36 mo 
100.0%
100.0%
0.0%
0.0%
0.0%
0.0%
6001-10000 hrs,
37-60 mo 
100.0%
50.0%
0.0%
50.0%
0.0%
0.0%
Show/hide table
 NOTE: This is a 6.0-hour job
NOTE: Register Affected Product in SIMSi if not already completed.

Show/hide table


PARTS DISPOSITION

Show/hide table
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
 
 
 

Information System:

PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REPLACING THE BOLT USED TO ATTACH THE 235-8862 MOUNT ASSEMBLY ON CERTAIN 325D MH FCR, 325D MH HCR, 330D MH FCR, 345C MH FCR, AND 345C MH HCR MATERIAL HANDLERS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM LOWERING CHECK VALVES ON CERTAIN 315D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE FRAME ON CERTAIN 312 LINKAGE PIN GRABBER QUICK HITCH HEX COUPLERS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 109-4440 PLUG ON ALL MP20 AND VT40 MULTIPROCESSORS
PRODUCT SUPPORT PROGRAM TO INSPECT AND REPLACE THE FUEL HOSE CONDUIT ON CERTAIN 345D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE MAIN CONTROL VALVE ON CERTAIN 345C, 345CL, 345D AND 345DL EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE HYDRAULIC CYLINDER RODS ON CERTAIN 319D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING THE CAB AIR DUCT ASSEMBLIES ON CERTAIN 321D AND 328D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE CYLINDER HEAD LIFTING EYE BOLT HOLE ON VARIOUS 3508, 3512, AND 3516 ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STEERING CYLINDER ON CERTAIN 414E, 416E, 420E, 422E, 428E, 430E, 432E, AND 442E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE ALL WHEEL STEER SYSTEM ON CERTAIN 432E, 434E, 442E AND 444E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM TO REPLACE THE 194-0820 BLOCK ON CERTAIN 330D L, 336D L, AND 330D MH FCR EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSPECTING, AND IF NECESSARY REPLACING, THE 179-2203 OUTER BOLTS OF THE SWING GEAR BEARING ON CERTAIN 365B, 365B SERIES II AND 365C EXCAVATORS THAT ARE CONFIGURED FOR MATERIAL HANDLING, ULTRA HIGH DEMOLITION OR OEMS APPLIC
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STICK CYLINDER ROD ON CERTAIN 365CL HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ENGINE PLATE REGARDING THE ENGINE POWER RATING ON CERTAIN 315D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING ECCENTRIC SHAFT BEARINGS ON CERTAIN CVP110 VIBRATORY PLATE COMPACTORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FUEL MANIFOLD (RAIL) ON CERTAIN C6.6 INDUSTRIAL ENGINES AND C6.6 ENGINES INSTALLED IN VARIOUS APPLICATIONS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE HYDRAULIC CYLINDERS ON CERTAIN 319D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE STICK AND BOOM CONTROL VALVE ON CERTAIN 303C CR, 303.5C CR, 304C CR, AND 305C CR EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING BUCKETS ON CERTAIN 312C, 312D, 315C, AND 315D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT IDLER GROUP ON CERTAIN 385B AND 385C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE "A" PORT PLUG AND THE BREATHER BOLT ON CERTAIN H180D S HYDRAULIC HAMMERS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE MAIN HYDRAULIC PUMP ON CERTAIN 385B, 385BL, 385BL MH, 5090BL, 385C, 385CL, 385CL MH AND 385C FS EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING NOISY BOOM LOWERING CHECK VALVES AND STICK LOWERING CHECK VALVES (IF INSTALLED) ON CERTAIN 312D, 315D, AND 319D EXCAVATORS