EPC Parts Catalogs

PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REMOVING 5I-7523 ENGINE SLEEVES FROM DEALER STOCK Caterpillar


  1. Home
  2. Service Letter-NACD
  3. #2545
`
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REMOVING 5I-7523 ENGINE SLEEVES FROM DEALER STOCK [REBE5134]
SERVICE EQUIPMENT AND SUPPLIES
PARTS STOCK, ORDERING & RETURN
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REMOVING 5I-7523 ENGINE SLEEVES FROM DEALER STOCK
REBE5134-01

Show/hide table
29Apr2009
(Revised 27May2009)


U-166
A-144
D-140
O-149

 
Show/hide table
Parts stock action only
  
  

PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REMOVING 5I-7523 ENGINE SLEEVES FROM DEALER STOCK
7750
PI70300
Show/hide table
NOTE:

When submitting claim for Parts Stock Action, Use the appropriate 99Z as the s/n, the appropriate Service Letter Program Number as the Part number in the Part Causing Failure field, "7751" as the Group Number, "56" as the Description Code.
Show/hide table
NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst.
Show/hide table
Show/hide table
 
NOTE:

This Revised Service Letter replaces the 29Apr2009 Service Letter. Changes have been made to Action Required.

Show/hide table

TERMINATION DATE
31Jul2009

PROBLEM

Show/hide table
The outside diameter of the 5I-7523 Engine Sleeve may not be within the tolerance range and may either be too loose and slide into the engine block or be too large and not fit correctly.

ACTION REQUIRED

Show/hide table
NOTE: 5I-7523 sleeves marked with "XX" on the box top have been inspected at AVSpare and should not be inspected again by the dealer. Refer to Image1.

Measure the outside diameter of the engine sleeve on three levels (top, middle, and bottom). For each level, take two measurements 90 degrees apart and average the numbers. The average number must be within the tolerance range of 105.070 mm and 105.100 mm.

- If the engine sleeve is not within the tolerance range, remove the engine sleeve from dealer stock and do not use.

- If the engine sleeve is within the tolerance range, the sleeve is acceptable for use. Mark the package to indicate the sleeve has been inspected according to PI70300 / REBE5134 and return to dealer parts stock.
Show/hide table
Image1

SERVICE CLAIM ALLOWANCES

Show/hide table
Submit one claim for all parts removed from dealer parts stock.

PARTS DISPOSITION

Show/hide table
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
 
 
 

Information System:

PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 129-5844 AND 215-7292 HOSES ASSEMBLIES THAT ARE USED IN THE STABILIZER LINES GROUP ON CERTAIN 416E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE ENGINE AIR INLET HOSES ON CERTAIN 325D AND 325D L EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE ENGINE AIR INLET HOSES ON CERTAIN 330D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REWORKING REMANUFACTURED 3508, 3512, 3516, AND 3524 CYLINDER HEADS (10R7765) THAT HAVE BEEN RECEIVED AT DEALERSHIPS WITH INCORRECT VALVE SPRINGS, ROTOCOILS, AND WASHERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE RADIATOR CORE ASSEMBLY ON CERTAIN 324D, 325D, AND M325D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE RADIATOR CORE ASSEMBLY AND ENGINE COOLANT TEMPERATURE REGULATOR ON CERTAIN 320D AND 323D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING A FAILED PUMP COUPLING ON CERTAIN 345C HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE LEAKING BOOM CYLINDER ASSEMBLY ON CERTAIN 385C FS AND 5090B HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE UPPER SWING FRAME PIN ON CERTAIN 420E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE LEAKING STICK CYLINDER ASSEMBLY ON CERTAIN 365BL, 365BL SERIES II AND 365CL EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE CAB AIR CONDITIONER INLET DUCT ON CERTAIN 314D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE VALVE SEAT IN THE IMPLEMENT PUMP CONTROLLER ON CERTAIN M313D, M315D, M316D, M318D, M318D MH, M322D, AND M322D MH WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REPLACING THE LINER SEAL PACKAGED WITH 0R8189, OR8187, OR8777, 0R8778, 10R1501, 10R1502, 10R2138, 10R5480, AND 10R6214 CYLINDER PACKS IN DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND POSSIBLY REWORKING 0R0997, 0R1000, 0R1001, 0R1002, 0R1003, 0R1004, 0R1005, AND 0R1006 REMAN WATER PUMPS IN DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REPLACING PISTONS AND PISTON RINGS ON CERTAIN C13 ENGINES INSTALLED IN VARIOUS 345C AND 345D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE TURBOCHARGER OIL SUPPLY TUBE SEAL ON CERTAIN C6.6 INDUSTRIAL ENGINES AND CERTAIN C6.6 ENGINES INSTALLED IN VARIOUS TRACK-TYPE TRACTORS, WHEELED EXCAVATORS, TRACK-TYPE LOADERS, C6.6 OLYMPIAN GENSETS, WHEEL LOA
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN PULLEY (FAN DRIVE) ON CERTAIN 320C, 321CCR, 320D, AND 323D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN PULLEY (FAN DRIVE) ON CERTAIN 320C, 321CCR, 320D, AND 323D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN PULLEY (FAN DRIVE) ON CERTAIN 320C(L) AND 320D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN PULLEY (FAN DRIVE) ON CERTAIN 320C, 321CCR, 320D, AND 323D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE EMISSIONS LABEL ON CERTAIN 345D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR UPDATING THE FUEL LINES ON CERTAIN 385C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FUEL INJECTION PUMP ON CERTAIN 414E IL, 416E, AND 420E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE HYDRAULIC LINES ON CERTAIN GSH15 AND GSH15B GRAPPLES