PRODUCT SUPPORT PROGRAM FOR REWORKING THE DOZER CYLINDER HOSES ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
[REBE3287]
HYDRAULIC SYSTEM
LINES GP-BLADE
PRODUCT SUPPORT PROGRAM FOR REWORKING THE DOZER CYLINDER HOSES ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
REBE3287-01
Show/hide table
| 14Mar2008 |
| (Revised 24Apr2008) |
D-98
Show/hide table
| Before/After | PRODUCT SUPPORT PROGRAM FOR REWORKING THE DOZER CYLINDER HOSES ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS |
|
| 5057 | PS42644 |
|
Show/hide table
| NOTE: | This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS42644" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code. |
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst. |
Show/hide table
| NOTE: | This Revised Service Letter replaces the 14Mar2008 Service Letter. The Rework Procedure was removed and changes have been made to the Service Claim Allowances and Action Required. |
Show/hide table
TERMINATION DATE |
| 31Mar2010 |
PROBLEM
Show/hide table
| The existing dozer cylinder hoses can fail on certain 305.5 Mini Hydraulic Excavators. The hoses can contact the ground and get damaged. If the existing hoses fail, they must be replaced with shorter hoses and the hose routing must be modified. |
AFFECTED PRODUCT
Show/hide table
| Model | Identification Number |
| 305.5 | CXZ00126-00595 DCK00177-00406 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
| 2 | 3J1907 | SEAL-O-RING |
| 4 | 6V8398 | SEAL-O-RING-ORFS |
| 2 | 3173533 | HOSE AS |
| In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 9% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
ACTION REQUIRED
Show/hide table
| Install new hose assemblies using the procedure that is described in Special Instruction REHS4573. |
Show/hide table
SERVICE CLAIM ALLOWANCES
Show/hide table
Show/hide table
| NOTE: This is a 3.0-hour job | ||||||
| The labor allowance includes time for local fabrication of the two hose supports described in the Special Instructions. |
Show/hide table
PARTS DISPOSITION
Show/hide table
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
Information System:
PRODUCT SUPPORT PROGRAM FOR RELOCATING THE HORN SWITCH TO THE FRONT CONSOLE ON CERTAIN 414E, 416E, 420E AND 430E BACKHOE LOADERS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE PUMP LINES ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PLATE FOR THE MUFFLER GROUP ON CERTAIN 365CL, 365CL FS, AND 365CL MH EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PLATE FOR THE MUFFLER GROUP ON CERTAIN 385C, 385CL, 385C FS, AND 385CL MH EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PLATE FOR THE MUFFLER GROUP ON CERTAIN 385B, 385BL, AND 5090B EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING LEAKING PILOT HOSES ON CERTAIN M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318D, M322C, M322D, M325C, M325D, AND M330D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE SWING MOTOR ON CERTAIN 365CL, 365CL FS, 365CL MH, 365CL OEM, 385B, 385BL, 385B OEM, 5090B, 385C, 385CL, 385C FS, 385CL MH, AND 385C OEM EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING OPERATOR CONSOLE SUPPORTS ON CERTAIN MEDIUM AND LARGE HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND RETURNING CERTAIN REMAN AIR COMPRESSORS
PRODUCT SUPPORT PROGRAM FOR REPLACING HARNESS RETAINING CLIPS ON CERTAIN 303C CR AND 303.5C CR MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE MAIN HYDRAULIC PUMP ON CERTAIN 330D, 330D L, 330D MH, 345C, 345C L, AND 345C MH HYDRAULIC EXCAVATORS IN THE CASE OF FAULTY SERVO PIN ADJUSTMENT
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE LOWER FRAME ON CERTAIN M325C, M325CL, M325D AND M325DL MH EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING A CHECK VALVE ON CERTAIN 345C AND 385C L EXCAVATORS THAT ARE EQUIPPED WITH THE ULTRA HIGH DEMOLITION (UHD) FRONT PARTS
PRODUCT SUPPORT PROGRAM FOR INSPECTING AND/OR REPLACING THE STICK CYLINDER ROD ON CERTAIN 385B AND 385C HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR FLASHING THE MACHINE CONTROL SOFTWARE ON CERTAIN 320D(L), 324D(L), 325D, AND 330D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING FAILED CONTROL GROUP HANDLE (177-7711 OR 177-7712) USED ON CERTAIN 312C, 315C, 318C, 319C, 320C, 321C CR, 322C, 325C, 330C, 330C MH, 330C OEM, 365B SERIES II, 365B SERIES II FS, 385B AND 5090B EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE HVAC UNIT BLEND DOOR ON CERTAIN MEDIUM WHEEL LOADERS AND FORESTRY MACHINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE RADIO CONVERTER ON VARIOUS EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE HYDRAULIC TANK ON CERTAIN 301.6C AND 301.8C MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE FINAL DRIVES ON CERTAIN 307C AND 308C CR MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STICK ASSEMBLY ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STICK ASSEMBLY ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR CHECKING AND REWORKING THE MACHINE INTERFACE MOUNTING FRAMES ON CERTAIN PC203, PC204, PC205, PC206 AND PC210 COLD PLANERS AND SW60 WHEEL SAWS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING MACHINES FROM SERVICE AND INSPECTING/REPLACING CYLINDERS ON CERTAIN 320D, 321D, 324D, 325D, AND 328D EXCAVATORS