EPC Parts Catalogs

PRODUCT SUPPORT PROGRAM FOR REPLACING THE PUMP SHAFT SEAL ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS Caterpillar


  1. Home
  2. Service Letter-Australia
  3. #2424
`
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PUMP SHAFT SEAL ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS [REBE4033]
BASIC ENGINE
PULLEY GP
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PUMP SHAFT SEAL ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
REBE4033-00

Show/hide table
04Nov2008


D-473

 
Show/hide table
After Failure Only
  
  

PRODUCT SUPPORT PROGRAM FOR REPLACING THE PUMP SHAFT SEAL ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
5070 1205 1207
PS51583
Show/hide table
NOTE:

This Program can only be administered after a failure occurs. The decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS51583" as the Part Number and "7755" as the Group Number. Use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.

Show/hide table
NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your AVSpare product analyst.
Show/hide table

Show/hide table

TERMINATION DATE
30Nov2010

PROBLEM

Show/hide table
The existing pump shaft seal can leak on certain 305.5 Mini Hydraulic Excavators. If the existing seal leaks, it must be replaced and modifications must be carried out in order to prevent dirt from entering the cavity for the pump drive coupling. Dirt entry causes wear to the seal lip.

AFFECTED PRODUCT

Show/hide table
Model Identification Number
305.5 CXZ00126-00725

DCK00177-00406

PARTS NEEDED

Show/hide table

Qty

 Part Number Description
1 1076661 SEAL-LIP TYPE
1 1516671 PULLEY
1 1905827 PULLEY-FAN
1 3196756 GROMMET
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 6% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table
Carry out the modifications that are described in Special Instruction, REHS3890. Drain the hydraulic oil into a clean container and re-use the hydraulic oil.
Note: In addition to the parts listed in the PARTS NEEDED section, you will need one tube of Loctite 32314 Fixmaster Metal Magic Steel per machine.
Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table
Product smu/age whichever comes first
AVSpare
Dealer Suggested
Customer Suggested
Parts %
Labor Hrs%
Parts %
Labor Hrs%
Parts %
Labor Hrs%
0-3000 hrs 
100.0%
100.0%
0.0%
0.0%
0.0%
0.0%
Show/hide table
 NOTE: This is a 5.0-hour job

Show/hide table


PARTS DISPOSITION

Show/hide table
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
 
 
 

Information System:

PRODUCT SUPPORT PROGRAM FOR REPAIRING THE REACH BOOM, IF CRACKED, ON CERTAIN 345B SERIES II AND 345C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE REAR IMPLEMENT LIFT SOLENOID ON CERTAIN 414E INDUSTRIAL LOADERS
PRODUCT SUPPORT PROGRAM FOR INSPECTING AND/OR REPLACING SWIVEL BOOT ON CERTAIN 365C L, 365C L MH, 365C L FS AND 365C OEM HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE HYDRAULIC TANK ON CERTAIN 330D AND 330DL EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE ENGINE OIL FILTER HOSES ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE AIR COOLING PIPE ASSEMBLY ON CERTAIN 330D, 330DL, 330D OEM AND 330D LN OEM EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE PUMP CONTROL VALVE ON CERTAIN 303C CR, 303.5C CR, 304C CR, AND 305C CR MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM TO CEASE OPERATION OF THE COUNTERWEIGHT REMOVAL SYSTEM ON CERTAIN 345B, 345B II AND 345C EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FRONT TRACK IDLER ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING TRACK ROLLERS ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE BOOM LOWERING CONTROL VALVES ON CERTAIN 323D, 324D, 325D, 330D AND 345C EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND TIGHTENING IF NECESSARY THE SWING GEAR BEARING BOLTS ON CERTAIN 320D AND 330D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE TRACK CARRIER ROLLERS ON CERTAIN 305.5 MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE BOLTS FOR THE MAIN PUMP SUCTION PIPE ON CERTAIN 319D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING BOOM, STICK, AND BUCKET CYLINDERS ON CERTAIN 330D MH, 345C, AND 345D EXCAVATORS
PRODUCT SUPPORT PROGRAM TO REPLACE THE MEDIUM PRESSURE RELIEF VALVE ON CERTAIN M313D, M315D, M316D, M318D, M318D MH, M322D AND M322D MH WHEELED EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTION AND REWORK OF THE REMANUFACTURED IMPLEMENT PUMP ON CERTAIN D5H, D6H, D6M, D9R, D8N, D8R TRACK-TYPE TRACTORS, 24H MOTOR GRADERS, 5130B MINING EXCAVATORS, 854G WHEEL DOZERS, AND 992G WHEEL LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE STARTER CABLE ROUTING ON CERTAIN 345C AND 345CL EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR FLASHING NEW MONITOR SOFTWARE ON CERTAIN M313D, M315D, M316D, M318D, M318D MH, M322D, AND M322D MH WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE 209-6862 SWING FRAME ASSEMBLY ON CERTAIN 428E, 432E, AND 434E BACKHOE LOADERS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REPLACING, IF NEEDED, THE BOOM AND BUCKET CYLINDERS ON CERTAIN 330D, 330D MH, 345C AND 345D EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REMOVING CERTAIN 289-0008 PULLER STUDS FROM DEALER AND CUSTOMER INVENTORY AND SERVICE FACILITIES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE STICK ON CERTAIN 320C, 320C L, 330C, AND 330C L HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING THE FLASH FILE ON CERTAIN M313D AND M315D WHEELED EXCAVATORS