Idlers (Track)
`
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
[UENR6291]
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Track
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Piston Motor (Propel)
UNDERCARRIAGE
IDLER GP
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Idlers (Track)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Idlers (Track)
Show/hide table
| |
| Illustration 1 | g06025517 |
Show/hide table
| Specification for 383-4237 Front Idler Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 1 | 7H-7131 Pipe Plug | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
| 2 | 2 | 482-9627 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Prior to assembly, apply a thin film of 6V-4876 Lubricant to the contacting surfaces of the metal seal rings. The metal seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist. |
| 3 | 2 | 099-0163 Pin | Install the pin with the slit in the range that is specified. The correct position of the pin is shown in view B-B. |
| C | - | - | Specified range is 30 degrees. |
| D | - | - | Angle from centerline of idler shaft is 15 degrees. |
| 4 | - | - | Prior to assembly, clean the surface to remove the protective coating. |
| 5 | 1 | 6I-6477 Idler Shaft | Install the idler shaft. Position the "R" that is stamped on the end face of the idler shaft backward into the front idler bearing. |
| - | - | - | End play in axial direction:
Minimum is Maximum is |
Information System:
323F Excavator
Maintenance Interval Schedule
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Track
New K Series GET Tips are Now Available for Certain Excavators and Wheel Loaders Buckets {6800, 6805}
349F XE and 352F XE Excavators
Engine Oil Level - Check
C9 Engines for Caterpillar Built Machines
Unit Injector Hydraulic Pump
C9 Engines for Caterpillar Built Machines
Cylinder Head Valves
New K Series GET Adapters are Available on Certain Excavators and Wheel Loaders Buckets {6001, 6800, 6803}
BH150 Backhoes and BH160 Backhoes For Skid Steer Loaders and Multi Terrain Loaders
Shipping
Improved Diesel Oxidation Catalyst (DOC) Is Used On Certain D Series Wheeled Excavators {1091}
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Control Valve
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Air Conditioner Lines
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems
Air Conditioner Lines
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train
Piston Motor (Propel)
An Improved Radiator is Now Used for Certain 300.9D, 301.4C, 302.7D CR Mini Hydraulic Excavators {1353, 1380}
Inspection and Rework Procedure for Swing Bearing Bolted Joint on Certain 305.5E and 306E Mini Hydraulic Excavators {7063}
Improved Electrical Grounding is Now Used on Certain 308E2 CR Mini Hydraulic Excavators {1408, 7301}
Installation Procedure for Auxiliary Relief Valves on Certain 308E2 CR Mini Hydraulic Excavators with an Updated Main Control Valve {5069, 5117}
A Procedure to Install Quick Coupler Hydraulic Line Mounting Brackets on Certain 307E2 Mini Hydraulic Excavators is Now Available {6502}
307E2 Mini Hydraulic Excavator Machine Systems
Main Control Valve - Assemble
C9 Engines for Caterpillar Built Machines
Crankshaft Seals
349D2 MHPU Mobile Hydraulic Power Unit Machine System
Upper Frame - Soilmec
349D2 MHPU Mobile Hydraulic Power Unit Machine System
Upper Frame - Standard
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Fuel Tank
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Hydraulic Cylinder (Conveyor Swing)