Track Roller (Single Flange)
`
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
[UENR6293]
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Control Valve and Mounting
UNDERCARRIAGE
ROLLER GP
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Track Roller (Single Flange)
Show/hide table
![]() | |
Illustration 1 | g06027119 |
Show/hide table
Specifications for 497-8871 Track Roller Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 2 | 497-8889 Roller Bushing As | Bore after assembly is |
2 | 2 | 6S-3285 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Before assembly, apply a thin layer of oil to the contacting surfaces of the metal seal rings. The seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist. Refer to Special Instruction, SEHS8364, "Assembly and Installation of Conventional Duo-Cone Seals" |
3 | 2 | 7D-9749 O-Ring Seal | Lubricate the bore lightly with the lubricant that is being sealed. |
- | - | - | End play for the track roller shaft:
Minimum is Maximum is |
Information System:
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Conveyor System
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Alternator - Remove and Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Operator Console
Installation Master Guide for the <NOBR>503-4975</NOBR> Auxiliary Control Ar on Certain Hydraulic Excavators {5051}
Installation of the <NOBR>255-2082</NOBR> Pilot Lines Gp on Certain Hydraulic Excavators {5057, 5059}
An Improved Power Converter is Available for Certain Excavators {7338}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Lines (Conveyor) - Motor
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Steering Cylinder
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Lines (Conveyor)
New Cat Grade Control / Cat Production Measurement Software is Now Available on Certain 336F XE and 349F XE Excavators {7494, 7610, 7620}
415F2 Backhoe Loaders Hydraulic and Steering System
Service Brake Control
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems
Control Valve and Mounting
301.7D CR Mini Hydraulic Excavator
Track Adjustment - Inspect
336D 2L and 340D 2L Excavators Machine Systems
Swing Gear and Bearing - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heating and Air Conditioning Unit - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Heater Core - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Evaporator Coil - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Cab - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems
Fuel Tank - Remove and Install
Improved Hoses Are Now Used on Certain Backhoe Loaders {5057}
New Rear Axle and Brake Control Groups Are Now Used On Certain 424B Backhoe Loaders {3278, 3282, 4269}
352F Mobile Hydraulic Power Unit (MHPU) Machine System
Main Hydraulic System
336D 2L and 340D 2L Excavators Machine Systems
Hydraulic Lockout Control - Remove and Install