Stick Cylinder
`
325C Excavator Machine System Specifications
[RENR5363]
325C Excavator Machine System Specifications
Control Valve (Main)
325C Excavator Machine System Specifications
Bucket Cylinder
HYDRAULIC SYSTEM
CYLINDER GP
325C Excavator Machine System Specifications
Stick Cylinder
325C Excavator Machine System Specifications
Bucket Cylinder
325C Excavator Machine System Specifications
Bucket Cylinder
Show/hide table
![]() | |
Illustration 1 | g03620365 |
Show/hide table
Specification for 179-9791 Stick Cylinder and Seal Gp , and 191-5589 Stick Cylinder and Seal Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 1     | 3B-8489 Grease Fitting     | Torque to 9.3 ± 4.9 N·m (82.3 ± 43.3 lb in).     |
2     | 2     | 186-5477 Bushing     | During press fit, insert the bushing from the taper side. Bore of the bushing before installation is 80.12 ± 0.02 mm (3.154 ± 0.001 inch). Installation depth is 7.5 mm (0.30 inch).     |
B     | 1     | 194-8361 Cylinder As     | Bore is 150 mm (5.9 inch).     |
C     | 1     | -     | Diameter of the rod is 105 mm (4.1 inch).     |
3     | 12     | 9X-2404 Bolt     | Torque to 520 ± 78 N·m (385 ± 60 lb ft).     |
4     | 1     | 194-8358 Locknut     | Torque to 13100 ± 655 N·m (9662 ± 483 lb ft).     |
5     | 1     | 096-6210 Socket Setscrew     | Torque to 57 ± 10 N·m (42 ± 7 lb ft). After tightening the socket setscrew, stake the socket setscrew in two places.     |
Information System:
2001/12/03
Correction to Service Magazine , "Use the Technical Information Feedback Systems" {0374}
312C Excavator Machine Systems
Blade Pump - Remove and Install
5230B Excavator Machine Systems
Selector Valve (Hydraulic Activation) - Install
3046 Engine for Caterpillar Built Machines
Fuel Injection Timing - Check - In-line Fuel Pump
5130B Excavator
Reference Material
W345B Series II Excavator Hydraulic System
Travel Motor - Test - Measurement of Case Drain Oil
345B, 345B Series II and W345B Series II Excavators Machine Systems
Main Control Valve - Assemble
W345B Series II Material Handler Machine Systems
Main Control Valve - Disassemble
5130B Excavator Hydraulic System
Piston Pump (Swing)
5130B Excavator Hydraulic System
Piston Pump (Swing)
W345B Series II Excavator Hydraulic System
Relief Valve (Line) - Test and Adjust
325C Excavator Machine System Specifications
Control Valve (Main)
312C and 312C L Excavator
Belt - Inspect/Adjust/Replace
Determining the Correct Part Numbers for Main Bearings and Cylinder Head Gaskets {1124, 1201, 1203}
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers
Transmission Oil - Change
446B Backhoe Loader Transmission (Autoshift)
Solenoid Valve (Autoshift)
3176C and 3196 Engines for Caterpillar Built Machines
Rear Power Take-Off (RPTO) - Disassemble
325C Excavator Hydraulic System
Pump Control (Negative Flow) - Test
3408E and 3412E Industrial Engines
System Overview
325C Excavator Machine System Specifications
Bucket Cylinder
312C Excavator Machine Systems
Shuttle Valve - Remove - Auxiliary Control
3176C and 3196 Engines for Caterpillar Built Machines
Rear Power Take-Off (RPTO) - Assemble
325C Excavator Machine System Specifications
Final Drive
312C Excavator Machine Systems
Shuttle Valve - Install - Auxiliary Control