325D and 329D Excavators and 325D Material Handler Machine System Specifications Fasteners - Swing Drive and Final Drive Caterpillar


Fasteners - Swing Drive and Final Drive
`
325D and 329D Excavators and 325D Material Handler Machine System Specifications [RENR7423]
FRAME AND BODY
MOUNTING GP
325D and 329D Excavators and 325D Material Handler Machine System Specifications Fasteners - Swing Drive and Final Drive


Illustration 1g02797394

Table 1
Specification for 171-9412 Swing and Final Drive Fastener Gp 
Item  Qty  Part  Specification description 
Before assembly, the surfaces must be clean and free from protective coating. 
40  470-0614 Bolt  Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize compound to the bolt threads.
Use the following tightening procedure:
1. Tighten bolts to 150 ± 25 N·m (111 ± 18 lb ft).
Turn to an additional 60 ± 5 degree 
16  461-3882 Bolt  Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize compound to the bolt threads.
Use the following tightening procedure:
1. Tighten bolts to 250 ± 25 N·m (184 ± 18 lb ft).
2. Turn to an Additional 45 ± 5 degree 
Before assembly, into the upper frame group, coat the mating surfaces with Loctite high flex GM. 
096-4755 Pin  Apply Loctite C5A copper antiseize to the pin surface. 
5D-1026 Band Clamp  Torque to 4.5 ± 0.5 N·m (39.8 ± 4.4 lb in)

Information System:

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Temperature Sensor Open or Short Circuit - Test
312C Excavator Machine Systems Accumulator - Remove and Install
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM Attachment Code - Configure
5230B Excavator Vital Information Management System (VIMS) Service Operations
5230B Excavator Vital Information Management System (VIMS) Normal Operation
5230B Excavator Vital Information Management System (VIMS) General Information
C-9 Engine for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Shipping the Machine
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting and Tying Down the Machine
312C Excavator Machine Systems Shuttle Valve - Install - Auxiliary Control
325C Excavator Machine System Specifications Final Drive
3176C and 3196 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Assemble
Procedure to Reinforce the Frame Assembly Stabilizer{7222}
312C Excavator Machine Systems Fuel Tank - Remove
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Swing Lock Pin Control
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - HDB Series Alternator
312C Excavator Machine Systems Fuel Tank - Install
305 CR Mini Hydraulic Excavator Access Door and Cover Locations
312C Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - HDB Series Alternator
305 CR Mini Hydraulic Excavator Capacities (Refill)
330B Excavator Machine System Specifications Track Carrier Roller
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Sound Information and Vibration Information
312C and 312C L Excavator Plate Locations and Film Locations