Boom - 6150 mm (242.1 inch)
`
325C Excavator Machine System Specifications
[RENR5363]
325C Excavator Machine System Specifications
Boom - 5550 mm (218.5 inch)
325C Excavator Machine System Specifications
Stick - M2.5D
IMPLEMENTS
BOOM GP
325C Excavator Machine System Specifications
Boom - 5550 mm (218.5 inch)
325C Excavator Machine System Specifications
Boom - 6150 mm (242.1 inch)
Show/hide table
![]() | |
Illustration 1 | g00778381 |
(A) Boom cylinder (B) Stick cylinder (C) Stick |
Note: All bores must be free of paint. Coat all bores for pins with lubricant.
Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.
(1) Two 186-5476 Sleeve Bearings
- Outside diameter ... 130.135 ± 0.012 mm (5.1234 ± 0.0005 inch)
- Inside diameter ... 110.300 ± 0.020 mm (4.3425 ± 0.0008 inch)
- Installation depth for the sleeve bearing in the bearing bore ... 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
- Inside diameter ... 110.300 ± 0.020 mm (4.3425 ± 0.0008 inch)
(2) Lubricate the sealing lip slightly with the lubricant that is being sealed.
(3) 186-5637 Pin
- Diameter after plating ... 89.850 ± 0.025 mm (3.5374 ± 0.0010 inch)
- Plating thickness for the first layer ... 0.015 mm (0.0006 inch)
- Plating thickness for the second layer ... 0.015 mm (0.0006 inch)
- Bore diameter for pin ... 90.043 ± 0.043 mm (3.5450 ± 0.0017 inch)
- Plating thickness for the first layer ... 0.015 mm (0.0006 inch)
(4) 4I-4618 Pin Assembly
- Diameter after plating ... 79.850 ± 0.025 mm (3.1437 ± 0.0010 inch)
- Minimum thickness for plating ... 0.005 mm (0.0002 inch)
- Bore diameter for pin ... 80.037 ± 0.037 mm (3.1511 ± 0.0015 inch)
- Minimum thickness for plating ... 0.005 mm (0.0002 inch)
(5) 186-5580 Pin
- Diameter after plating ... 99.850 ± 0.025 mm (3.9311 ± 0.0010 inch)
- Minimum thickness for plating ... 0.005 mm (0.0002 inch)
- Bore diameter for pin ... 100.043 ± 0.043 mm (3.9387 ± 0.0017 inch)
- Minimum thickness for plating ... 0.005 mm (0.0002 inch)
(6) Use the necessary shims to adjust the lateral clearance.
- Maximum clearance ... 0.8 mm (0.03 inch)
- 133-2427 Shim ... 0.5 mm (0.02 inch)
- 093-0090 Shim ... 1.0 mm (0.04 inch)
- 166-1488 Shim ... 2.0 mm (0.08 inch)
- 133-2427 Shim ... 0.5 mm (0.02 inch)
Information System:
305 CR Mini Hydraulic Excavator
Engine Air Filter Primary Element - Clean/Replace
3500B, 776D, 777D, 784C, 785C, 789C, 793C and and 793D Off-Highway Truck/Tractors
Refrigerant Compressor
325C Excavator Machine System Specifications
Boom - 5550 mm (218.5 inch)
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Controller Input and Output Values
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Speed Sensor - Replace
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Proportional Reducing Valve - Calibrate
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Proportional Reducing Valve Sweep - Test
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Electronic Governor - Calibrate
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Digital Output On/Off - Test
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Engine Speed Dial Setting - Check
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Hydraulic Hammer - Adjust
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Parameter - Adjust
305 CR Mini Hydraulic Excavator
Engine Oil Level - Check
M315 Excavator Hydraulic System
Engine Performance - Test
CS44 and CP44 Soil Compactor Machine System
Vibratory Support
M315 Excavator Hydraulic System
Engine Speed - Test and Adjust - No Load
305 CR Mini Hydraulic Excavator
Engine Oil and Filter - Change
315C Excavator
Engine Speed Control
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2
Check of Governor Actuator - Troubleshoot - CID 91 - 315C, 318C, 319C, 320C, 321C, And 322C
2001/09/24
New Main Bearings Provide Improved Bearing Retention in the Cylinder Block {1203}
5130B Excavator Hydraulic System
Pilot Hydraulic System
325C Excavator Machine System Specifications
Stick - M2.5D
325C Excavator Machine System Specifications
Stick - M3.2C
3500B and 3500B High Displacement Generator Set Engines
E017 High Engine Coolant Temperature Warning