325C Excavator Machine System Specifications Stick Caterpillar


Stick
`



Illustration 1g00777651

(A) Stick cylinder

(B) Boom

(C) Bucket cylinder

(D) Bucket control linkage

(E) Bucket

Note: All bores must be free of paint. Coat all bores for pins with lubricant.

Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.

(1) 4I-4915 Pin Assembly

Diameter after plating ... 69.850 ± 0.025 mm (2.7500 ± 0.0010 inch)
Minimum thickness for plating ... 0.005 mm (0.0002 inch)
Bore diameter for pin ... 70.0 mm (2.76 inch)

(2) Use the necessary shims to adjust the lateral clearance.

166-1486 Shim ... 2.0 mm (0.08 inch)

(3) 4I-4914 Pin Assembly

Diameter after plating ... 79.850 ± 0.025 mm (3.1437 ± 0.0010 inch)
Minimum thickness for plating ... 0.005 mm (0.0002 inch)
Bore diameter for pin ... 80.0 mm (3.15 inch)

(4) Lubricate the sealing lip slightly with the lubricant that is being sealed. Install the dust seal so that the lip faces to the outside. Refer to the detail. Install the seal so that the seal does not extend beyond the face of the boss.

(5) Two 186-5465 Sleeve Bearings

Outside diameter ... 116.155 ± 0.011 mm (4.5730 ± 0.0004 inch)
Inside diameter ... 100.290 ± 0.020 mm (3.9484 ± 0.0008 inch)
Installation depth for the bearing in the bearing bore ... 9.5 ± 0.8 mm (0.37 ± 0.03 inch)

(6) Two 163-3749 Sleeve Bearings

Outside diameter ... 85.160 ± 0.013 mm (3.3527 ± 0.0005 inch)
Inside diameter ... 70.267 ± 0.037 mm (2.7664 ± 0.0015 inch)
Installation depth for the bearing in the bearing bore ... 7.5 ± 0.8 mm (0.30 ± 0.03 inch)

(7) Two 186-5588 Sleeve Bearings

Outside diameter ... 95.180 ± 0.013 mm (3.7472 ± 0.0005 inch)
Inside diameter ... 80.69 ± 0.43 mm (3.1768 ± 0.0169 inch)
Installation depth for the bearing in the bearing bore ... 7.5 ± 0.8 mm (0.30 ± 0.03 inch)

Information System:

3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks E021 High Exhaust Temperature Derate
312C and 312C L Excavator Lifting Capacities - 312C L with a Reach Boom and No Blade
3500B and 3500B High Displacement Generator Set Engines E017 High Engine Coolant Temperature Warning
325C Excavator Machine System Specifications Stick - M3.2C
325C Excavator Machine System Specifications Stick - M2.5D
5130B Excavator Hydraulic System Pilot Hydraulic System
2001/09/24 New Main Bearings Provide Improved Bearing Retention in the Cylinder Block {1203}
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Check of Governor Actuator - Troubleshoot - CID 91 - 315C, 318C, 319C, 320C, 321C, And 322C
315C Excavator Engine Speed Control
305 CR Mini Hydraulic Excavator Engine Oil and Filter - Change
M315 Excavator Hydraulic System Engine Speed - Test and Adjust - No Load
CS44 and CP44 Soil Compactor Machine System Vibratory Support
312C and 312C L Excavator Joystick Controls
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control No Power Supply to Controller - Troubleshoot
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control Fuel Gauge Indication Is Abnormal - Troubleshoot - 420A and 420B
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control Hydraulic Oil Temperature Gauge Indication Is Abnormal - Troubleshoot - 4203
325C Excavator Machine System Specifications Stick
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Engine Controller Is Abnormal - Troubleshoot - 590
305 CR Mini Hydraulic Excavator Fuses - Replace
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks E095 Fuel Filter Restriction Warning
325C Excavator Machine System Specifications Stick
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E099 Engine Oil Filter Restriction Warning
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Mounting Bracket
2001/10/15 Correction to Systems Operation, Testing and Adjusting , "Pump Control (Negative Flow) - Test" {5070}