325C Excavator Machine System Specifications Stick - R2.65C Caterpillar


Stick - R2.65C
`



Illustration 1g00777651

(A) Stick cylinder

(B) Boom

(C) Bucket cylinder

(D) Bucket control linkage

(E) Bucket

Note: All bores must be free of paint. Coat all bores for pins with lubricant.

Note: Make sure that the bearings are installed in the bore so that the identification numbers of the bearings are facing outward.

(1) 4I-4915 Pin Assembly

Diameter after plating ... 69.850 ± 0.025 mm (2.7500 ± 0.0010 inch)
Minimum thickness for plating ... 0.005 mm (0.0002 inch)
Bore diameter for pin ... 70.0 mm (2.76 inch)

(2) Use the necessary shims to adjust the lateral clearance.

166-1486 Shim ... 2.0 mm (0.08 inch)

(3) 4I-4914 Pin Assembly

Diameter after plating ... 79.850 ± 0.025 mm (3.1437 ± 0.0010 inch)
Minimum thickness for plating ... 0.005 mm (0.0002 inch)
Bore diameter for pin ... 80.0 mm (3.15 inch)

(4) Lubricate the sealing lip slightly with the lubricant that is being sealed. Install the dust seal so that the lip faces to the outside. Refer to the detail. Install the seal so that the seal does not extend beyond the face of the boss.

(5) Two 186-5465 Sleeve Bearings

Outside diameter ... 116.155 ± 0.011 mm (4.5730 ± 0.0004 inch)
Inside diameter ... 100.290 ± 0.020 mm (3.9484 ± 0.0008 inch)
Installation depth for the bearing in the bearing bore ... 9.5 ± 0.8 mm (0.37 ± 0.03 inch)

(6) Two 163-3749 Sleeve Bearings

Outside diameter ... 85.160 ± 0.013 mm (3.3527 ± 0.0005 inch)
Inside diameter ... 70.267 ± 0.037 mm (2.7664 ± 0.0015 inch)
Installation depth for the bearing in the bearing bore ... 7.5 ± 0.8 mm (0.30 ± 0.03 inch)

(7) Two 186-5588 Sleeve Bearings

Outside diameter ... 95.180 ± 0.013 mm (3.7472 ± 0.0005 inch)
Inside diameter ... 80.69 ± 0.43 mm (3.1768 ± 0.0169 inch)
Installation depth for the bearing in the bearing bore ... 7.5 ± 0.8 mm (0.30 ± 0.03 inch)

Information System:

5230B Excavator Machine Systems Piston Motor (Air Conditioner) - Remove and Install
325C LCR Excavator Machine System Specifications Stick - R3.0C
305 CR Mini Hydraulic Excavator Hydraulic System Oil Level - Check
3524B Engines for Off-Highway Trucks E272 Inlet Air Restriction Warning
315C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E173 High Exhaust Temperature Warning
3046 Engine for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
2001/10/15 Correction to Systems Operation, Testing and Adjusting , "Pump Control (Negative Flow) - Test" {5070}
H45/H45 S, H50/H50 S, 63/H63/H63 S, 70/70 S/H70/H70 S, H90C/H90C S and 100/H100/H100 S Hydraulic Hammers Mounting Bracket
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E099 Engine Oil Filter Restriction Warning
325C Excavator Machine System Specifications Stick
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks E095 Fuel Filter Restriction Warning
312C and 312C L Excavator Capacities (Refill)
312C and 312C L Excavator Cooling System Hoses - Inspect
305 CR Mini Hydraulic Excavator Hydraulic System Oil - Change
325C Excavator Machine System Specifications Stick - R3.2C
C-9 Engine for the 330C Excavator and for the 330C Mobile Hydraulic Power Unit Sensors and Electrical Connectors
2001/11/19 Prerequisites for Flashing Software into Machine Electronic Control Modules {7620}
CS56B, CP56B, CS66B, CS68B and CP68B Vibratory Soil Compactors Machine Systems Vibratory Support - Disassemble
5230B Excavator Machine Systems Control Valve (Rear) - Disassemble
312C and 312C L Excavator Blade Control
5230 Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
303.5 Mini Hydraulic Excavator Work Tool Control
303.5 Mini Hydraulic Excavator Work Tool Flow Control