374D Excavator Machine System Specifications Stick - 2.57 m (8.432 ft) Caterpillar


Stick - 2.57 m (8.432 ft)
`


Illustration 1g03506191

Table 1
Specification for 324-1211 Hoe Stick Gp 
Item  Qty  Part  Specification Description 
All the bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all the bores for the pins, the bucket, and the cylinder pin bores. 
The stick cylinder must be assembled in order to orient the grease zerk, as shown in Illustration 1. 
367-1444 Pin As  Diameter is 119.85 ± 0.04 mm (4.718 ± 0.002 inch)
As required, use the following shims to adjust the maximum lateral clearance to 1.0 mm (0.04 inch)
1 147-3957 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0074 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0106 Shim  Thickness is 2.0 mm (0.08 inch)
As required, use the following shims to adjust the maximum lateral clearance to 1.0 mm (0.04 inch)
1 151-0653 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0076 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0108 Shim  Thickness is 2.0 mm (0.08 inch)
367-1436 Pin As  Diameter is 129.85 ± 0.04 mm (5.112 ± 0.002 inch)
9X-4597 Lip Type Seal  Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed.
Install the dust seal so that the lip faces outside, as shown.
Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. 
9X-4600 Lip Type Seal  Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed.
Install the dust seal so that the lip faces outside, as shown.
Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. 
9X-4601 Lip Type Seal  Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed.
Install the dust seal so that the lip faces outside, as shown.
Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. 
234-3748 Bushing(1)  Bore before assembly is 140.38 ± 0.04 mm (5.527 ± 0.002 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
10  7Y-9914 Bushing(1)  Bore before assembly is 100.29 ± 0.02 mm (3.948 ± 0.001 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
11  269-1600 Bushing(1)  Bore before assembly is 130.26 ± 0.02 mm (5.128 ± 0.001 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
(1) Install the bushing in the bore so that the part number of the bushing is facing outward.

Information System:

374D Excavator Machine System Specifications Boom - 7.00 m (23.0 ft)
349E Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations
Installation of the 300-1190 Auxiliary Hydraulic Lines Gp {5057}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Condenser - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Crossover) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Refrigerant Receiver-Dryer - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Compressor - Remove and Install
2010/04/28 Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM 3G Electrical Connector - Inspect
568 Forest Machine Hydraulic System Swing Speed and Overswing on Level Ground - Check
568 Forest Machine Hydraulic System Travel on Level Ground - Test - Optional Test
374D Excavator Machine System Specifications Stick - 3.60 m (11.8 ft)
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Oil Pan - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Daily Inspection
MP15, MP20, MP30 and MP40 Multi-Processors Declaration of Conformity
C13, C15, and C18 Tier 4 Interim Engines Sensor Signal (Analog, Passive) - Test
MP15, MP20, MP30 and MP40 Multi-Processors Work Tool Installation and Removal
2010/04/15 A New Torque Is Used for Installing the Check Valve Gp into the Secondary Fuel Filter Base on Certain Machine Engines {1261, 1274, 5067}
349F and 352F Excavators Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Bucket Linkage Bearings and Seals - Remove and Install
Procedure to Repair The Welds on Certain Excavators Track Roller and Car Body Frames{0679, 4150, 4151, 7062}
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
374D Excavator Machine System Specifications Boom Cylinder