Pilot Lines - System 23
`
312D and 313D Excavators Machine System Specifications
[KENR6553]
312D and 313D Excavators Machine System Specifications
Pump Lines
312D and 313D Excavators Machine System Specifications
Control Valve - Two Pump One Way Flow
HYDRAULIC SYSTEM
LINES GP-HYDRAULIC
311D Excavator Machine System Specifications
Pilot Lines
312D2 and 313D2 Excavators Machine System Specifications
Pilot Lines - Joystick and Main Control Valve
312D and 313D Excavators Machine System Specifications
Pilot Lines - Pump
312D and 313D Excavators Machine System Specifications
Pilot Lines - Main Control Valve and Manifold
314D CR Excavator Machine System Specifications
Stick Cylinder Lines
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 23
Show/hide table
 | |
| Illustration 1 | g02171173 |
Top view | |
Show/hide table
| Required Parts List | |||
| Item | Qty | Part | Specification Description |
| - | - | - | Sharp corners at the cutting edge of each cable strap shall not be allowed. |
| 1 | 1 | 309-5769 Pressure Switch | Torque to 29 ± 3 N·m (257 ± 27 lb in). |
Show/hide table
 | |
| Illustration 2 | g02579736 |
Typical example Rear view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 2 | 1 | 150-3036 Elbow As | Torque to 40 ± 5 N·m (30 ± 4 lb ft). |
| 3 | 2 | 5C-9553 Bolt | Torque to 9.8 ± 1.5 N·m (86.7 ± 13.3 lb in). |
| 4 | 1 | 285-2663 Fitting As | Torque to 29 ± 3 N·m (257 ± 27 lb in). |
Show/hide table
 | |
| Illustration 3 | g02579739 |
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 5 | 3 | 148-8378 Elbow As | 24 ± 2 N·m (212 ± 18 lb in). |
Information System:
S365C and S385C Demolition and Scrap Shears
Jaw - Repair
S365C and S385C Demolition and Scrap Shears
Cutting Edge Bolts - Tighten
S365C and S385C Demolition and Scrap Shears
Cutters - Inspect/Replace
C27 and C32 Generator Set Engines
Fuel Lines - Remove and Install
Product Link - PL522/523
Diagnostic Capabilities
S365C and S385C Demolition and Scrap Shears
Lifting and Tying Down
S365C and S385C Demolition and Scrap Shears
Transport Position - Transport of shear on host machine
S365C and S385C Demolition and Scrap Shears
Operation
C13, C15, and C18 Tier 4 Interim Engines
Exhaust Balance Valve - Test
Product Link - PL522/523
General Information
S365C and S385C Demolition and Scrap Shears
Work Tool Installation and Removal
S365C and S385C Demolition and Scrap Shears
Declaration of Conformity
312D and 313D Excavators Machine System Specifications
Control Valve - Two Pump One Way Flow
312D and 313D Excavators Machine System Specifications
Front Lines
349E Excavator Hydraulic System
Solenoid Valve (Fine Swing) - If Equipped
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 20
Product Link - PL522/523
Event Code List
Product Link - PL522/523
Electronic Service Tool Does Not Communicate with ECM
349E Excavator Hydraulic System
Travel Hydraulic System
Rework Procedure for the Insulation Group Around the Cooling Arrangement for 307D Excavators{7150, 7251, 726A, 7276, 7301}
Product Link - PL522/523
Reports and Messages Not Available
374D Excavator Hydraulic System
Specifications
312D and 313D Excavators Machine System Specifications
Front Lines - System 22
C4.4 Industrial Engine
Engine Oil Pump - Inspect