Control Valve - Two Pump One Way Flow
`
312D and 313D Excavators Machine System Specifications
[KENR6553]
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 23
312D and 313D Excavators Machine System Specifications
Front Lines
HYDRAULIC SYSTEM
VALVE GP-CONTROL
325D and 329D Excavators and 325D Material Handler Machine System Specifications
Pilot Valve (Joystick)
325D and 329D Excavators and 325D Material Handler Machine System Specifications
Pilot Valve (Joystick)
325D and 329D Excavators and 325D Material Handler Machine System Specifications
Pilot Valve (Joystick)
312D and 313D Excavators Machine System Specifications
Control Valve - Two Pump One Way Flow
312D2 and 313D2 Excavators Machine System Specifications
Control Valve
312D and 313D Excavators Machine System Specifications
Main Control Valve
Show/hide table
 | |
| Illustration 1 | g02550916 |
Show/hide table
| Specification for 310-0157 Control Valve Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 2 | 5A-3604 Bolt | Torque to 26.95 ± 2.45 N·m (238.53 ± 21.68 lb in). |
| 2 | 1 | 197-0148 Bolt | Apply Loctite thread sealant. Torque to 17 ± 1 N·m (150 ± 9 lb in). |
| 3 | 2 | 197-0225 Plug As | Torque to 73.5 ± 4.9 N·m (54.2 ± 3.6 lb ft). |
| 4 | 1 | 197-0150 Spring | Free length is 35.9 mm (1.41 inch). |
| 5 | 1 | 197-0151 Spring | Free length is 67.5 mm (2.66 inch). |
| 6 | 1 | 170-9997 Plug | Torque to 36.5 ± 2.5 N·m (26.9 ± 1.8 lb ft). |
| 7 | 1 | 7I-7206 Plug | Torque to 140 ± 10 N·m (103 ± 7 lb ft). |
| 8 | 1 | 7I-7207 Spring | Free length is 23 mm (0.9 inch). |
| 9 | 2 | 197-0165 Bolt | Torque to 26.95 ± 2.45 N·m (238.53 ± 21.68 lb in). |
| 10 | 1 | 310-0062 Relief Valve Gp | Torque to 73.5 ± 4.9 N·m (54.2 ± 3.6 lb ft). |
Information System:
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 23
S365C and S385C Demolition and Scrap Shears
Jaw - Repair
S365C and S385C Demolition and Scrap Shears
Cutting Edge Bolts - Tighten
S365C and S385C Demolition and Scrap Shears
Cutters - Inspect/Replace
C27 and C32 Generator Set Engines
Fuel Lines - Remove and Install
Product Link - PL522/523
Diagnostic Capabilities
S365C and S385C Demolition and Scrap Shears
Lifting and Tying Down
S365C and S385C Demolition and Scrap Shears
Transport Position - Transport of shear on host machine
S365C and S385C Demolition and Scrap Shears
Operation
C13, C15, and C18 Tier 4 Interim Engines
Exhaust Balance Valve - Test
Product Link - PL522/523
General Information
S365C and S385C Demolition and Scrap Shears
Work Tool Installation and Removal
312D and 313D Excavators Machine System Specifications
Front Lines
349E Excavator Hydraulic System
Solenoid Valve (Fine Swing) - If Equipped
312D and 313D Excavators Machine System Specifications
Pilot Lines - System 20
Product Link - PL522/523
Event Code List
Product Link - PL522/523
Electronic Service Tool Does Not Communicate with ECM
349E Excavator Hydraulic System
Travel Hydraulic System
Rework Procedure for the Insulation Group Around the Cooling Arrangement for 307D Excavators{7150, 7251, 726A, 7276, 7301}
Product Link - PL522/523
Reports and Messages Not Available
374D Excavator Hydraulic System
Specifications
312D and 313D Excavators Machine System Specifications
Front Lines - System 22
C4.4 Industrial Engine
Engine Oil Pump - Inspect
312D and 313D Excavators Machine System Specifications
Pump Lines (Auxiliary)