5230B Excavator Vital Information Management System (VIMS) Service Operations Caterpillar


Service Operations
`

Numerous VIMS service operations can be initiated by the operator or a service technician. A unique service program code (SPC) is assigned to each of the service operations. The service program codes are entered through the VIMS keypad module. Entering the service program code starts the corresponding service operation. The service operations are listed in Table 1.

Table 1
VIMS Service Operations    
Service Operation     Service Program
Code    
Service Program
Code    
Page
Number    
"Attachment Code - configure"     "ATTACH"     288224     ??    
"Data Logger - Reset "     DLRES     (35737)     11    
"Data Logger - Start/Stop"     DLOG     (3564)     12    
"Display Backlighting - Set"     BLT     (258)     12    
"Display Contrast - Set"     CON     (266)     12    
"Display Language - Set"     LA     (52)     13    
"Display Units - Set"     UN     (86)     13    
"Event Acknowledged - Show"     EACK     (3225)     15    
"Event List - Show"     ELIST     (35478)     15    
"Event Statistics - Show"     ESTAT     (37828)     16    
"Lubrication Cycle Time - Set"     LUBSET     (582738)     16    
"Lubrication Manual - Start"     LUBMAN     (582626)     17    
"Machine Status - Show"     MSTAT     (67828)     18    
"Resettable Totals - Reset"     RESET     (73738)     19    
" Resettable Totals - Show"     TOT     (868)     19    
"Service Lamp - Reset"     SVCLIT     (782548)     19    
"Service Lamp - Set"     SVCSET (1)     (782738)     19    
"Snapshot Trigger - Configure"     ERSET (1)     (37738)     22    
System Self Test     TEST     (8378)     24    
"VIMS Snapshot - Start"     EREC     (3732)     26    
( 1 ) The service tool is required to be connected and communicating with the machine before this SPC is active.

Each service program code is a unique number of one to ten digits that abbreviates this operation. The service program codes have a letter equivalent that describes the service operation. This letter equivalent makes remembering the service program code for each operation easier. The English letter equivalent for each service program code is shown in the parentheses. The same service program codes are used regardless of the onboard language.

After you enter the service program code on the keypad, the request will begin after you press the "OK" key. You must activate this command within five seconds of entering the last SPC character. The maximum delay that is allowed between the entry of the SPC characters is five seconds .

Information System:

5230B Excavator Vital Information Management System (VIMS) Normal Operation
5230B Excavator Vital Information Management System (VIMS) General Information
C-9 Engine for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Shipping the Machine
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting and Tying Down the Machine
312C Excavator Machine Systems Shuttle Valve - Install - Auxiliary Control
325C Excavator Machine System Specifications Final Drive
3176C and 3196 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Assemble
312C Excavator Machine Systems Shuttle Valve - Remove - Auxiliary Control
325C Excavator Machine System Specifications Bucket Cylinder
3408E and 3412E Industrial Engines System Overview
325C Excavator Hydraulic System Pump Control (Negative Flow) - Test
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM Attachment Code - Configure
312C Excavator Machine Systems Accumulator - Remove and Install
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Temperature Sensor Open or Short Circuit - Test
325D and 329D Excavators and 325D Material Handler Machine System Specifications Fasteners - Swing Drive and Final Drive
Procedure to Reinforce the Frame Assembly Stabilizer{7222}
312C Excavator Machine Systems Fuel Tank - Remove
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Swing Lock Pin Control
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - HDB Series Alternator
312C Excavator Machine Systems Fuel Tank - Install
305 CR Mini Hydraulic Excavator Access Door and Cover Locations
312C Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - HDB Series Alternator