854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM Attachment Code - Configure Caterpillar


Attachment Code - Configure
`
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMS<SUP>TM</SUP> [RENR6318]

The following information describes the service program code: 288224 (ATTACH)

This service program allows the operator to configure the attachment code for the Large Hydraulic Excavators. The Attachment Code is the software version of the Harness Code. The harness code is a hard wired configuration of jumper wires that ground certain circuits in a harness code plug. The VIMS broadcasts the attachment code via the AVS data link to other electronic control modules on the machine that need this code.

Note: Applicable attachment codes are listed on the back of machine Electrical Schematic and in the Operations and Maintenance Manual.

Note: VIMSpc must be connected and communicating with the machine in order to change the 288224 (ATTACH) code.

After "ATTACH" is entered from the keypad, the operator presses the "OK" key. The message center will show:




Illustration 1g00485847

The desired attachment code can then be entered from the keypad by entering the desired attachment code. Then press the "OK" key. If a valid attachment code has been entered, the message center will prompt the operator to re-enter the attachment code. The message center will show:




Illustration 2g00485848

If the same code is entered again, this code will be accepted as the new attachment code. If the same code is not entered at the second prompt, the new attachment code will not be accepted. The old attachment code remains valid. A new attachment code will not be accepted, if an invalid code is entered at either prompt. The old attachment code remains valid. If the "OK" key was pressed at either prompt prior to entering a number, the old attachment code remains valid.

Note: The Machine Status (MSTAT) (67828) code can be used to view the present, active attachment code.

Information System:

5230B Excavator Vital Information Management System (VIMS) Service Operations
5230B Excavator Vital Information Management System (VIMS) Normal Operation
5230B Excavator Vital Information Management System (VIMS) General Information
C-9 Engine for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Shipping the Machine
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting and Tying Down the Machine
312C Excavator Machine Systems Shuttle Valve - Install - Auxiliary Control
325C Excavator Machine System Specifications Final Drive
3176C and 3196 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Assemble
312C Excavator Machine Systems Shuttle Valve - Remove - Auxiliary Control
325C Excavator Machine System Specifications Bucket Cylinder
3408E and 3412E Industrial Engines System Overview
312C Excavator Machine Systems Accumulator - Remove and Install
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Temperature Sensor Open or Short Circuit - Test
325D and 329D Excavators and 325D Material Handler Machine System Specifications Fasteners - Swing Drive and Final Drive
Procedure to Reinforce the Frame Assembly Stabilizer{7222}
312C Excavator Machine Systems Fuel Tank - Remove
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Swing Lock Pin Control
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - HDB Series Alternator
312C Excavator Machine Systems Fuel Tank - Install
305 CR Mini Hydraulic Excavator Access Door and Cover Locations
312C Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Disassemble - HDB Series Alternator
305 CR Mini Hydraulic Excavator Capacities (Refill)