Cylinder Drift - Check - Loaded Bucket
`
538 Forest Machine Machine Systems
[M0067938]
538 Forest Machine Machine Systems
Cylinder Drift - Check - Empty Bucket
538 Forest Machine Machine Systems
Cylinder Speed - Check
HYDRAULIC SYSTEM
CYLINDER GP
538 Forest Machine Machine Systems
Cylinder Drift - Check - Empty Bucket
538 Forest Machine Machine Systems
Cylinder Drift - Check - Loaded Bucket
538 Forest Machine Machine Systems
Cylinder Speed - Check
1.1. Specification
2.1. Introduction
3.1. Required Tools
4.1. Test Procedure
Show/hide table
"Cylinder Drift - Check (Loaded Bucket)" | |||
---|---|---|---|
Item | 538 GF | 538 LL | Actual |
Boom Cylinder | |
|
|
Stick Cylinder | |
|
|
Heel Cylinder | - | |
The performance level of the cylinder, the cylinder seals, and the overload relief valves for the implements can be determined with the following procedure.
Note: The machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools | |
---|---|
Description | Qty |
Measuring Tape | 1 |
Stopwatch | 1 |
Show/hide table
![]() | |
Illustration 1 | g00298378 |
- Position the machine on level ground. Refer to Illustration 1.
- Load the bucket.
- Raise the boom until the top stick pin is the same height as the boom foot pin.
- Fully extend the bucket cylinder.
- Fully retract the stick cylinder.
- Extend the stick cylinder rod
70 mm (2.8 inch) from the fully retracted position. - Measure each cylinder length from cylinder pin to cylinder pin.
- Stop the engine.
- Leave the machine in this position for 3 minutes. Measure each cylinder length from cylinder pin to cylinder pin for drift.
Information System:
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
General Information
538 Forest Machine Machine Systems
Cylinder Drift - Check - Empty Bucket
325F Excavator Machine Systems
Travel Motor - Remove and Install
538 Forest Machine Machine Systems
Swing Speed and Swing Drift on a Slope - Check
538 Forest Machine Machine Systems
Swing Speed and Overswing on Level Ground - Check
538 Forest Machine Machine Systems
Travel on Level Ground - Test
325F Excavator Machine Systems
Counterbalance Valve (Travel) - Assemble
GSV520 and GSV525 Orange Peel Grapples
Hydraulic Cylinder - Disassemble
314F and 315F Excavators Machine System Specifications
Air Conditioner Lines
314F and 315F Excavators Machine System Specifications
Communication Electronic Control Module (Product Link)
314F and 315F Excavators Machine System Specifications
Communication Electronic Control Module (Product Link)
314F and 315F Excavators Machine System Specifications
Cab Window
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Service Tools
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Connector Locations
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Diagnostic Capabilities
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System
Symptom Troubleshooting
538 Forest Machine Machine Systems
Cylinder Speed - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Engine Performance - Test - Engine Speed
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Travel on Level Ground - Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Travel on Level Ground - Test - Optional Test
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Swing Speed and Overswing on Level Ground - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Cylinder Drift - Check
303.5E2 CR, 304E2 CR, 304.5E2 XTC, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Hydraulic System
Cylinder Speed - Check
325F Excavator Engine Supplement
Refrigerant Condenser and Mounting - Remove and Install