325C Excavator Hydraulic System Engine Performance - Test - Engine Speed Caterpillar


Engine Performance - Test - Engine Speed
`
325C Excavator Hydraulic System [RENR5365]
BASIC ENGINE
325C Excavator Hydraulic System Engine Performance - Test - Engine Speed

Table 1
Required Tools    
Part Number     Description     Qty    
9U-7400     Multitach Tool Group     1    

  1. Position the machine on level ground.

  1. Stop the engine.

  1. Install 9U-7400 Multitach Tool Group on the engine.

  1. Start the engine.

  1. Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).

  1. Read the engine speed display (rpm) on the multitach. Refer to Table 2 for the specifications for engine speed at the desired engine operation.

Table 2
Item     Specifications    
New Rebuild     Service Limit    
No load high idle (1)     1880 ± 50 rpm (2)     1680 to 1930 rpm (1)    
1980 ± 50 rpm (3) 1780 to 2030 rpm (3)    
No load low idle     950 ± 50 rpm     950 ± 100 rpm    
Maximum speed with load (4)     1720 rpm (5)     1670 rpm (5)     1620 rpm (5)    
No load speed (6)     1300 ± 50 rpm     1300 ± 100 rpm    
( 1 ) AEC switch in the OFF position
( 2 ) Three seconds after the engine speed dial was placed at position "10"
( 3 ) Engine rpm within three seconds after the engine speed dial was placed at position "10"
( 4 ) Pressure is relieved from both pumps (stall condition).
( 5 ) Minimum rpm
( 6 ) AEC switch in the ON position

Note: A New specification is the performance that can be expected for a new machine. A Rebuild specification is the performance that can be expected after rebuilding the components of a system. Performance beyond the Service Limit is an indication of these problems: improper maintenance or adjustment, component wear and failure.

Information System:

5230B Excavator Machine Systems Control Valve (Swing) - Disassemble
325C Excavator Hydraulic System Operational Checks
325C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
305 CR Mini Hydraulic Excavator Hydraulic Lockout Control
5230B Excavator Machine Systems Control Valve (Swing) - Assemble
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
Installation Instructions for the 174-1508 Electric Motor {5927}
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
305 CR Mini Hydraulic Excavator Hydraulic System Specifications
5230B Excavator Machine Electronic Control System Sensors
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a VA Boom
305 CR Mini Hydraulic Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
5130B Excavator Sampling Interval and Location of Sampling Valve
325D and 329D Excavators Hydraulic System Travel on Level Ground - Test
325C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
325D and 329D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
325D and 329D Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
325C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
325D and 329D Excavators Hydraulic System Cylinder Speed - Check
325C Excavator Hydraulic System Specifications
312C Excavator Machine Systems Main Hydraulic Pump - Install
325C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust