325C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test Caterpillar


Travel on Level Ground - Test - Optional Test
`

Note: When the procedure for the Travel On Level Ground cannot be performed, this test may be used as a substitute.

Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.

Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".

Table 1
Required Tools    
Part Number     Description     Qty    
    Stopwatch     1    



Illustration 1g00297292

  1. Start the engine.

  1. Position the machine on level ground.

  1. Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).

  1. Raise a track off the ground. Refer to Illustration 1.

  1. Put a mark on a shoe of the raised track.

  1. Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.

  1. Place the travel speed control switch in HIGH position.

  1. Move the travel lever of the raised track to full travel position.

  1. Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction.

  1. Place the travel speed control switch in the LOW position and repeat Steps 8 through 9.

Table 2
325C Time For Three Revolutions (time in seconds)    
Travel Speed     New     Rebuild     Service Limit    
HIGH     Forward     19.0 or less     20.0 or less     22 or less    
Reverse
LOW     Forward     32.0 or less     33.0 or less     35.0 or less    
Reverse

Table 3
325C L Time For Three Revolutions (time in seconds)    
Travel Speed     New     Rebuild     Service Limit    
HIGH     Forward     20.5 or less     21.5 or less     23.5 or less    
Reverse
LOW     Forward     35.0 or less     36.0 or less     38.0 or less    
Reverse

Information System:

325D and 329D Excavators Hydraulic System Travel on Level Ground - Test
5130B Excavator Sampling Interval and Location of Sampling Valve
325C Excavator Hydraulic System Engine Performance - Test - Engine Speed
5230B Excavator Machine Systems Control Valve (Swing) - Disassemble
325C Excavator Hydraulic System Operational Checks
325C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
305 CR Mini Hydraulic Excavator Hydraulic Lockout Control
5230B Excavator Machine Systems Control Valve (Swing) - Assemble
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
Installation Instructions for the 174-1508 Electric Motor {5927}
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Lifting Capacities - M318C Excavator with a One-Piece Boom
305 CR Mini Hydraulic Excavator Hydraulic System Specifications
325D and 329D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
325D and 329D Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
325C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
325D and 329D Excavators Hydraulic System Cylinder Speed - Check
325C Excavator Hydraulic System Specifications
312C Excavator Machine Systems Main Hydraulic Pump - Install
325C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
325C Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust
325C Excavator Specifications
325C Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
W345B Series II Material Handler Hydraulic System Travel Motor