Water Pump - Test
`
3046 Engine for Caterpillar Built Machines
[SENR6457]
3046 Engine for Caterpillar Built Machines
Electric Starting System - Test
3046 Engine for Caterpillar Built Machines
Fuel Injection Timing - Check - In-line Fuel Pump
COOLING SYSTEM
3408E and 3412E Engines for Caterpillar Built Machines
Water Temperature Regulator - Test
3064 and 3066 Engines for Caterpillar Built Machines
Cooling System - Check - Overheating
3046 Engine for Caterpillar Built Machines
Cooling System - Test
3046 Engine for Caterpillar Built Machines
Water Pump - Test
Show/hide table
| Tools Needed | ||
| Part Number | Part Name | Quantity |
| 6V-7775 | Air Pressure Gauge | 1 |
Show/hide table
 | |
| Illustration 1 | g00820896 |
(1) Port | |
Show/hide table
 |
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts. When working on an engine that is running, avoid contact with hot parts and rotating parts. |
 |
Perform the following procedure in order to determine if the water pump is operating correctly:
- Remove the plug from port (1).
- Install the 6V-7775 Air Pressure Gauge in port (1) .
- Start the engine. Run the engine until the coolant is at operating temperature.
- Note the water pump pressure. The water pump pressure should be 80 kPa (12 psi) at rated speed and rated load.
Information System:
3126B Engine for Caterpillar Built Machines
Throttle Lock Switch Circuit - Test
312C Excavator Machine Systems
Blade - Remove and Install
325D and 329D Excavators Hydraulic System
Bypass Valve (Return) - Bypass Check Valve
325D and 329D Excavators Hydraulic System
Check Valve (Return Makeup) - Slow Return Check Valve
37-MT, 41-MT, and 42-MT Series Starting Motors
Starting Motor Solenoid - Test
325C Excavator Hydraulic System
Return Hydraulic System
322C Excavator Hydraulic System
Swing Hydraulic System
325C Excavator Hydraulic System
Travel Counterbalance Valve
3046 Engine For Caterpillar Built Machines
Fuel Shutoff Solenoid - Remove and Install
M313C and M315C Excavators
Axle Oil (Rear) - Change
Quick Coupler Wedge Lock(Wheel Loader)
Model View Illustrations
W345B Series II Material Handler Hydraulic System
Pilot Valve (Joystick)
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Solenoid Valves
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Related Components
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
General Information
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Using Service Mode
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Parameter Status Checks
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Using Caterpillar Electronic Technician
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Troubleshooting Diagnostic Codes
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
General Information (Electrical System)
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Start and Stop Circuit
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
Starting Aid Circuit
345B, 345B Series II and W345B Series II Excavators Engine and Pump Control
No Power Supply to Controller - Troubleshoot
325C Excavator Machine System Specifications
Main Hydraulic Pump